And they operate on 10-30 volts so you can put them on anything.
Updated rear bumper pics (was Project LXXIV)
- Thread starter cruiseroutfit
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
And they operate on 10-30 volts so you can put them on anything.
They are nice. Right now I have the kaymar off...but the entire time I was using it...those LEDs never burned out or gave me any issue.
The bumper I am using now for the time being has LEDs built in in the same fashion but they have burned out three times already. I gave up on them and yes I wired them properly...just like the LEDs on the Kaymar....
Tidy! who makes those?
They came from Moto-rage. A 4wd parts business in Japan. Had to use Dave Stedman as a middle man to buy them but I think the are on yahoo store too. I was never able to get them to sell me direct.
リアバンパーサイド – モトレージ - https://www.moto-rage.co.jp/product/%e3%83%aa%e3%82%a2%e3%83%90%e3%83%b3%e3%83%91%e3%83%bc%e3%82%b5%e3%82%a4%e3%83%89
I really liked them but had to remove them when I installed the kaymar.
Just curious, but have y'all gotten around to mocking out a 77 specific bumper?
- Thread starter
- #386
We have not. I’ve got a 77 so it may happen one day.
- Thread starter
- #387
Back-ordered rear bumpers are all shipping today! 
We do have a couple of front with/hoop available and a couple of rear dual swing setups available for immediate order/shipping. Next batch is due late winter.
We do have a couple of front with/hoop available and a couple of rear dual swing setups available for immediate order/shipping. Next batch is due late winter.
One thing that's not clear, is the hitch part of the bumper or does it bolt to the 4 holes in the center of the rear frame where a pintle would mount?
I see it's rated for Class 1 loads and is a 2-inch receiver.
I have a modified 80 series class 3 on my troopy, I guess I can keep it, if there's enough room/clearance, and then not worry about using the included hitch for higher loads.
I see it's rated for Class 1 loads and is a 2-inch receiver.
I have a modified 80 series class 3 on my troopy, I guess I can keep it, if there's enough room/clearance, and then not worry about using the included hitch for higher loads.
- Thread starter
- #389
It's separate, it bolts on with (6) bolts. In order to use bigger/better hardware, we remove the captured nuts on the front side of the frame channel and run grade hardware in the four locations.
Pics from instructions:
I'm not sure there would be room for a class 3 with the bumper, I suspect not.
Kurt,Ha. Require cutting out the rear cross-member of a frame and you offer a "I like the clean lines...". But a few holes in a door are just "interesting"? Give us some more credit than that lol.
How many people mind drilling? While it is a great question, it has nothing to do with this bumper. See, we worked with Toyota to pre-install all of the needed holes in the door
View attachment 1213512
For the 70 series trucks with the spare under the truck, is the door sheet metal reinforced enough to mount to?
- Thread starter
- #393
We’ve seen both. For those lacking the reinforcement from the factory, reinforcement plates on the four RH door bolts are easy.
- Thread starter
- #395
A customer shared some pictures of a inexpensive ATV storage box he found for mounting on the LH carrier. Our sales team thought it was cool and we though others might dig it. No affiliation: https://www.tractorsupply.com/tsc/product/tractor-supply-utv-storage-box-2811cb05c
You need one Dave!
- Thread starter
- #399
Finally on our website. As I've mentioned before in this thread and via PM, we've never held enough stock of these bumpers to warrant the time to put them on our website, i.e. demand has out-paced our supply ability. That has changed with the last few batches as we upped quantities and frequency. So with all of our back-orders shipped, we've added available inventory to our CruiserTeq.com site
FRONT w/HOOP:
cruiserteq.com
REAR w/DUAL SWING:
cruiserteq.com
We'll continue to flesh out the product details and included parts but I'm excited to finally have these available for immediate order.
FRONT w/HOOP:
Cruiser Outfitters 70 Series Front Bumper - with Hoop - Fits 7x Series Land Cruiser Applications (BUMP7XFRW)
Cruiser Outfitters 70 Series Front Bumper - with Hoop - Fits 7x Series Land Cruiser Applications (BUMP7XFRW)
cruiserteq.com
REAR w/DUAL SWING:
Cruiser Outfitters 70 Series Dual Swing-out Rear Bumper - Fits 7x Series Land Cruiser Applications (BUMP7XRDS)
Cruiser Outfitters 70 Series Dual Swing-out Rear Bumper - Fits 7x Series Land Cruiser Applications (BUMP7XRDS)
cruiserteq.com
We'll continue to flesh out the product details and included parts but I'm excited to finally have these available for immediate order.
Finally on our website. As I've mentioned before in this thread and via PM, we've never held enough stock of these bumpers to warrant the time to put them on our website, i.e. demand has out-paced our supply ability. That has changed with the last few batches as we upped quantities and frequency. So with all of our back-orders shipped, we've added available inventory to our CruiserTeq.com site
FRONT w/HOOP:
Cruiser Outfitters 70 Series Front Bumper - with Hoop - Fits 7x Series Land Cruiser Applications (BUMP7XFRW)
Cruiser Outfitters 70 Series Front Bumper - with Hoop - Fits 7x Series Land Cruiser Applications (BUMP7XFRW)
REAR w/DUAL SWING:
Cruiser Outfitters 70 Series Dual Swing-out Rear Bumper - Fits 7x Series Land Cruiser Applications (BUMP7XRDS)
Cruiser Outfitters 70 Series Dual Swing-out Rear Bumper - Fits 7x Series Land Cruiser Applications (BUMP7XRDS)
We'll continue to flesh out the product details and included parts but I'm excited to finally have these available for immediate order.
Has anyone attempted to fit the factory PTO winch to that front bumper?
Asking for a friend
