Drivetrain decisions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 12, 2021
Threads
15
Messages
122
Location
st louis
I have been blessed with a wealth of options and I'm looking for thoughts and opinions on which way to go.
I have a 70 FJ40 on 35s with a moderately healthy SBC. I'm building it to drive around town and some light wheeling in the midwest (think mud and trees not giant boulders)
  • It currently has a 3 speed with a vac actuated transfer case, but no hi/low linkage so I will need to source or fabricate that.
  • I currently have a 4 speed that just needs a light rebuild.
  • I have a great deal on a complete 4 speed drivetrain (trans, case, brake and linkage with 50k miles on it)
  • I also have a great looking quote for an Orion and twin sticks that would mate up to the 4 speed I have.
So here is the question. With those options in mind, would you
  1. Run a 4 speed with a 3 speed case and fab up some shifter linkage?
  2. Run a complete 4 speed/split case setup?
  3. Run a 4 speed into an Orion with twin sticks?
  4. Something else entirely?
 
How much have you set aside for all this? I would consider moving away from Toyota stuff altogether. Maybe a stock Ford 9" rear with disc brakes. Then maybe a nv4500 and dana 300 or atlas. Everything would be easily upgradable as needed. Easy parts availability. If toyota a 4 or 5 speed with a split case with a full floater 9.5" toyota axle of your choice behind it.
 
How much have you set aside for all this? I would consider moving away from Toyota stuff altogether. Maybe a stock Ford 9" rear with disc brakes. Then maybe a nv4500 and dana 300 or atlas. Everything would be easily upgradable as needed. Easy parts availability. If toyota a 4 or 5 speed with a split case with a full floater 9.5" toyota axle of your choice behind it.
I've already rebuilt the axels and converted to 4 wheel disc brakes, so the rest of the driveline is in pretty grand shape. I'll need driveshafts of course and did eye going to an automatic for a bit.
 
With your current setup my guess is that you have a Chevy bellhousing with an adapter plate for the Toyota 3 spd. At the very minimum you're going to need a new bellhousing for whichever transmission you decide to go with. Depending on the cost of your great deal for "complete 4 speed drivetrain (trans, case, brake and linkage with 50k miles on it)" this might be the least expensive route but you'll still need to factor in the new bellhousing.

As was previously mentioned the NV4500 route would also give you overdrive but with 35" tires that may not be needed. However, with lower first gear it would make taking off easier in tricky situations. Normal operation would act more like 3 spd with overdrive as starting in 2 nd gear works good at least with 33" tires. The NV4500 also puts the shift lever back to factory 3 spd shifter location.
 
I think White Stripe is spot on. I would consider a 4 or 5 speed/split case or something else. Thru the yrs of wheeling I found i wanted more low range gearing off road, and these days with fuel prices the 5 speed is something to consider. I went thru various drivelines to get where I'm now. Sbc,sm420, dana 20 and centered the stk rear-end so I could keep my Detroit Locker 4.88's and discs. Back then my options were limited. My understanding is the split case is stronger than the 1 piece and can handle moderate V8 power and has aftermarket gearing options. I personally prefer center rear output cases, which is how my street friendly trail rig is setup with 35" boggers. I've never run a splitcase. My other 40 runs a PO installed sbc, nv4500, and 1 piece tcase and 33s. This 40 won't see hard core trails so I'll nurse the 1 piece case along. I may change it to a split case and arb's in the future along with 35s. I like the low 1st gear and the overdrive. I've geared it to more street/highway friendly and a fairly capable lower range. Running a sbc allows for a wide range of trans/tcase setups but most will have a stronger centered rear output. The limiting factor is fitting a driveline into a short wheel base 40. I think the Orion is too expensive for what it is.
 
Last edited:
I switched from SM420/3 spd case to H42/ split case with 3:1 low range. Gives me better splits around town and more usable low range off road and a much quieter transfer case on the road.
Yes, 1st / low range is not as low as it used to be but frankly the 70:1 that I had before isn’t usable hardly anywhere east coast, not dry and sticky enough.
 
I'm building it to drive around town and some light wheeling in the midwest (think mud and trees not giant boulders)
For this purpose, your option #2 would be my choice.
 
For driving around town and light wheeling you dont need an orion, atlas or nv4500 , find a use downey bellhousing and use the 4 speed set-up , or keep the 3 speed and find a non vacuum early case
Or just get the conversion for the vacuum transfer case. Mine had the conversion and I converted it back to vacuum actuation. Its pretty unique as far as early 4x4 vehicles. Pretty cool in my opinion. Everyone has different taste though.

I have a sbc and 3speed. I dont mind the 3 speed. its a little differnt than I learned on being that it has the unsyncro 1st. not good for any hwy driving though. I also dont ever drive mine faster than 45 - 50mph.

I really want to just swap the engine for a stock f with a sniper or a b series diesel. If I had all the money in the world I would do some sort of ev conversion where I could still shift a manual trans haha. I have seen a few like this (even a 40) would be prettyt cool.
 
I am using a Toyota H55F and split transfer case for my build and converted an FJ60 axle to full floater. The transfer case has 3:1 low range.
 
Those two gear boxes cost a little more than the truck was new when I bought it in 1978.
 
Running 35" tires, what gear ratio in the diffs? Running 3:70s versus 4.88s makes a difference in your transmission choice. Stock you have 4.11s. a lower first gear won't be a bad option. 4.88s a H42 would probably be a better street transmission.
still the factory 4.11s for now, and probably the foreseeable future. I'm more likely to go to 33s before I regear.
 
When I was figuring out what driveline I wanted I used an rpm calculator online so I could see what my highway rpms are at certain speeds. I was considering 3.70 or 4.11s.

I also made charts using my gear ratios. My 1st chart was the trans I was running, because I knew how it drove and what gears I liked on the trail and driving on the street. Across the top list gear ratios of you trans. 1st,2nd,3rd. The Down column, list high range and low range ratios. And do the math for each gear in high and low and include the diff ratio as a multiplier too.

Now make charts for the trans and t cases combos your considering and compare those #'s with your current driveline. It will allow you to figure out what you like and where your current set up is lacking.
 
I like the split transfer cases because of option of low range gears. In real life most cruisers spend their life on pavement and off road in high range. Would plan for street driving then do a low different than stock in the transfer case if you think you would need it enough to justify it. I really like the gearing in the H42. I just wish Toyota would have made overdrive transmission with the same gearing and fifth gear OD. See plenty of late H42 for sale fairly cheap. Only thing missing is the countershaft to convert H55F. Not going to happen so leaves with aftermarket ODs to work with H42. Now sure the Ranger is still available to work with a V8. Other than that options a very limited.
 
Whats the consensus on a target cruising RPM and target cruising highway speed for an F/2f engine? None of my 40’s have tachs…. We only have so much HP, and are driving a brick down the highway, its really annoying to have to shift down at every slight incline because it takes all the HPs to keep the truck at speed and there isnt any power left to climb a small hill. This is a result of my form over function setup of a 3 spd trans, 4.11 diff gears and 37” tires, but curious what an ideal setup is to stay in the “power band” of these old tractor engines.
 
Back
Top Bottom