For Sale BJ60 3B Parts, Clutch, Slave, Master, Fork

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Owyhee Jackass

Owyhee Jackass

10 Year 15 Year 20 Year
Joined
Apr 1, 2004
Threads
253
Messages
3,583
Location
Boise, Id
Location
United States
I have a pile of parts I need to clear out. These are out of a 1984 BJ60, buyer pays shipping from 83702.

Intake Manifold - $75 - SOLD, Glenn

Exhaust Manifold - $75

Power Steering Pump and Bracket - $100 SOLD, DieselCruiser81

Upper and Lower Thermostat Housing - $50 - SOLD, Georg

Valve Cover - $40

Air Box - $40 - SOLD, Georg

Backing Plate - Make Offer - SOLD, Georg

Bell Housing (internal ribs ground for larger flywheel) (was bolted to H55/14BT) - $40 - SOLD

'Almost New' clutch - $150

12V Starter - $150 - SOLD Paul

12V Alternator w/vacuum pump - $150 SOLD, Paul

Misc. Elect. (fuse block, 12v preheat timer) - SOLD, Glenn

All prices are OBO. These were in a parts vehicle and mileage/operation is unknown.

I can get better photos if needed.


P1050301.webp


P1050302.webp


P1050303.webp


P1050304.webp


P1050306.webp
 
Last edited:
Hey Dan!
I'll take the air box, backing plate ( unless it's rusted out at the bottom ) and complete thermostat housing.
Shipped to:
Valley Hybrids 1038 W. Fremont St. Stockton CA 95203
Let me know how much including shipping.
Thanks bud!!!!

Georg @ Valley Hybrids & Cruiser Brothers
 
orangefj45 said:
Hey Dan!
I'll take the air box, backing plate ( unless it's rusted out at the bottom ) and complete thermostat housing.
Shipped to:
Valley Hybrids 1038 W. Fremont St. Stockton CA 95203
Let me know how much including shipping.
Thanks bud!!!!

Georg @ Valley Hybrids & Cruiser Brothers
Click to expand...


Give me a day or two to box it up. The backing plate is not rusty, I'll post up pictures later. Do you want the air-box plumbing (outlet to intake hoses) as well?
 
DieselCruiser81 said:
How much to ship the power tearing pump no bracket shipped to 77523?
I'm looking for one for my 83' BJ42.
Click to expand...

It should fit in a USPS medium flat rate box. $50 for just the pump, shipped.
 
Splangy said:
I'll take the steering pump if Georg takes just the bracket.
Click to expand...

@DieselCruiser81 is in line ahead of you, I need to get the bracket and pump separated first...hope to not destroy the pulley in the process.
 
Owyhee Jackass said:
@DieselCruiser81 is in line ahead of you, I need to get the bracket and pump separated first...hope to not destroy the pulley in the process.
Click to expand...

So, true... I have a warped one. The previous owner of the one I have forgot to mention he had unsuccessfully removed/damaged the pulley.
 
Last edited:
Great Success! (somewhat) Impact wrench did the trick, but there is a bit of a mark on the pulley.

As I was asking $100 for both, hows $50 for the pump and $50 for the bracket sound? @DieselCruiser81 The pump won't fit in a medium flat rate, but it will fit in a large. I'll put the bracket in with the other parts you want Georg. I'll send you a PM with the total + shipping.

P1050324.webp
P1050325.webp
P1050326.webp
P1050327.webp
 
@Owyhee Jackass did you use a puller to get pulley & pump separated? Did the impact wrench alone do the trick?
 
You must log in or register to reply here.

Share this page

Back
Top Bottom