97 Center Diff lock stuck

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 14, 2018
Threads
3
Messages
26
Location
Austin, TX
I recently got my first Land Cruiser sometime last week. I gotta say I'm already hooked. However, I am already running into a few issues. The main one at the moment is that the Center Diff light and ABS light is stuck on. I put it in Low Range when i went to go test the truck off road, and when i took it out of low range, the 2 lights stayed on. When i got back on the road, i didnt feel the truck bind at all. However, today when i drove it to school, it started to bind when i pulled into the parking lot.

I'm lost on this one. Anyone have any suggestions?
Thanks.
 
Welcome to Mud. It’s impossible to know what’s going on from your description. One thing I always encourage is for new owners to get a copy of the Toyota factory service manual. It’s indespensible in repairing, maintaining and getting to know your Landcruiser.

The first and easiest thing to do is to cycle the shifter into and out of low range many times in an attempt to free up the CDL actuator. You could do this in an area where you can actually drive over terrain requiring 4x4 and possible wheel spin.

You could also remove the rear drive shaft and see how well it travels up a slight hill. If it goes as usual, the CDL is still engage and your indication lights are telling the truth

There is also the possibilty of it being a indication problem only.
 
When it's shifted high to low, do you hear the relay in the kick panel click and the actuator on the transfer briefly run?
 
When it's shifted high to low, do you hear the relay in the kick panel click and the actuator on the transfer briefly run?
This is a logical path but, I have never heard a darn thing when I engage my cdl.
 
This is a logical path but, I have never heard a darn thing when I engage my cdl.
As he said, i dont hear a thing when i switch it from low to high or vice versa. I will look into finding a factory service manual. I'm a little tight on budget atm but ill still see if i can find one for less than a $100. I will try switching it from low to high a bunch. Thank you for the advice.
 
You can get the FSM for free. Someone has the pdfs posted in the classifieds somewhere (I still don't understand why it's there and not stickied somewhere). For the life of me I can't find the link.

On the problem, definitely cycle it a lot. Generally the CDL doesn't get used a lot on these things before people like us get a hold of them so they can be sticky. If you get a CDL switch it's easy to install and easy to cycle a lot to exercise it (I got mine for about $65 on ebay). The free version is putting it in and out of 4 low a lot. Sometimes you have to drive and turn a bit to get it to lock and unlock. Good luck!
 
You can get the FSM for free. Someone has the pdfs posted in the classifieds somewhere (I still don't understand why it's there and not stickied somewhere). For the life of me I can't find the link.

On the problem, definitely cycle it a lot. Generally the CDL doesn't get used a lot on these things before people like us get a hold of them so they can be sticky. If you get a CDL switch it's easy to install and easy to cycle a lot to exercise it (I got mine for about $65 on ebay). The free version is putting it in and out of 4 low a lot. Sometimes you have to drive and turn a bit to get it to lock and unlock. Good luck!

Thank you! I have been looking into getting the CDL switch but I just can't seem to find it at a half decent price, but I will continue to look.
I will definitely root around and see if I can find those FSMs.
 
As he said, i dont hear a thing when i switch it from low to high or vice versa. I will look into finding a factory service manual. I'm a little tight on budget atm but ill still see if i can find one for less than a $100. I will try switching it from low to high a bunch. Thank you for the advice.
Turn the key to the on position, don't start the engine, then shift the transfer case. You should hear the relay and the CDL motor.
 
I had kind of the same problem with mine, the lady i brought my truck from never used 4 low in the 19 years she owned it. What i did to fix my problem, i removed the center diff lock switch from the transfer case, cleaned it with spray contact cleaner, then reinstalled it. From not being used, it was all gummed up inside causing the ball detent to stick. It took me less time to cleaning it, then it did to remove and reinstall it, but cleaning it was way cheaper then spending 65 bucks on a new one. Here's a photo off what the switch looks like, and here's a link to a thread by another member who had the same problem as you.
DIFF LOCK Light ON!! Cant turn it OFF!!! HELP!!!!
312268865_aa76049271.jpg
 
Yep, I would start with the indicator switch that's shown above.

Either shift back into L and H a few times on a dirt road, or if that doesn't work (It usually does), you can remove it and just clean the switch.
 
Note- if the driveline is actually binding, the indicator switch is not your problem. Post up when you have an answer to Tools R Us's question.

When it's shifted high to low, do you hear the relay in the kick panel click and the actuator on the transfer briefly run?

Turn the key to the on position, don't start the engine, then shift the transfer case. You should hear the relay and the CDL motor.
 
I took it out on a dirt road this evening and tried to get it fixed. Unfortunately, after switching through high and low several times, it did not seem to come undone. I tried turning it off and switching it from high to low, but did not hear anything. I am going to try to take the switch part off and clean it this weekend.
 
Camtman here are a few more links and photos. Credit for these photos and part numbers goes to Mud member ZackR.
Here is a step by step guide on how to remove that switch with photos.
CDL Sensor/Switch
Heres the part number for the factory switch along with some aftermarket part numbers.
BECK/ARNLEY Part # 2011788
NAPA P/N NS6421
Autozone P/N JA449
upload_2018-1-10_12-51-26-png.1607922

Below is a photo of a transfer case so you can see where the switch is located.

upload_2018-1-11_11-23-29-png.1608473
 
Note- if the driveline is actually binding, the indicator switch is not your problem. Post up when you have an answer to Tools R Us's question.


Maybe not... If the switch is stuck “on” the center diff will stay locked, even if the selector is in high...

Crawl under the truck and just unplug the aforementioned switch... if all goes away your switch is stuck, in a much less common way of “on”...

EDIT: shorted together switch wiring could also cause this
 
Last edited:
There are several ways it can fail, both mechanically and electrically, so clues to what works and doesn't, greatly speeds finding the problem. My first test is; does the actuator motor run, if not, does the relay click, knowing that gives direction for testing. This thread has info on the system, page 3 has the explanation from the NCF document on how it works: CDL Actuator Fun
 
Camtman here are a few more links and photos. Credit for these photos and part numbers goes to Mud member ZackR.
Here is a step by step guide on how to remove that switch with photos.
CDL Sensor/Switch
Heres the part number for the factory switch along with some aftermarket part numbers.
BECK/ARNLEY Part # 2011788
NAPA P/N NS6421
Autozone P/N JA449
upload_2018-1-10_12-51-26-png.1607922

Below is a photo of a transfer case so you can see where the switch is located.

upload_2018-1-11_11-23-29-png.1608473


Thanks very much. I will definitely be using this this weekend.
 
There are several ways it can fail, both mechanically and electrically, so clues to what works and doesn't, greatly speeds finding the problem. My first test is; does the actuator motor run, if not, does the relay click, knowing that gives direction for testing. This thread has info on the system, page 3 has the explanation from the NCF document on how it works: CDL Actuator Fun

I will be giving this a read as well.
 
Back
Top Bottom