transmission

Out of an HZJ77, 1992, 150k km on both. It is a part-time transfer case. Asking $900 $500 for both. Must be picked up, will not seperate. Sold together.

Looking for transmission and transfer case for 1994 LC FJ80 - OEM parts numbers above. Thanks.

I believe my H 55 is still original. Was wondering what would be going out to make 1st and reverse harder to difficult to engage. Starting thinking about the need to rebuild or replace in the near future.

Don’t want to ship this. Extremely heavy. What is in the picture is what is there. I don’t have and linkage. Came out of a 65’ that was swapped to a floor shift 3-speed. Make an offer.

From a running and driving 1993 80 series; 239,410 miles; No smoke or rattles etc. - $1,500 for engine and transmission package! ....not interested in separating... I bought this rig for mainly interior parts but the thing ran so well I couldn't resist tooling around on my property in it before...

Came off of a running truck. $100 plus ship.

I just picked up a used 2019 GX460 Premium. The vehicle has everything that I wanted except for a few items: external radiator/transmission cooler, full-length fuel tank skid plate and trailer hitch. I got the trailer hitch installed by a nearby Lexus dealership while addressing a recall for...

Wanted: transmission tunnel in good condition.

I have a 3bii engine I bought as a spare that I do not anticipate using for the foreseeable future. 2k This was from a 24volt 70 series but will replace any B/3b diesels.

‘79 FJ40 4 speed transmission and transfer case. Purchased from a fellow Mudder years ago and never used. Been stored inside a shed since I had it, but looks like it may have been outside before. Price $300 local pickup ‘79 Bellhousing 2F $100 local pickup ‘79 Flywheel 2F $75 local pickup...

Looking for one 1976/77 for a 2F fj40.

Dipstick assembly from a 1994 A442f. Complete and undamaged. $50 plus shipping

Located in Delaware. Greetings folks, would like to sell the motor and tranny that’s currently in my wife’s 60 series. Going to diesel Motor and tranny are currently in the truck, come drive it before you buy it. Has a Holley Sniper on it, sale includes carb that came off and spare. Also brand...

Hi there, my cousin gifted me his 91 Land Cruiser when he passed away last year. Do to logistics, and repairs, I just got it. The LC was in Montana, then hauled to Washington, then finally transported to my house in CA, I had a transmission, and new drive shaft installed before I had it...

Asking 1500 for engine and transmission. Head looks rebuilt hei dui distributor 6 - 1 exhaust header Stock carburetor Compression #'s 1 - 170 2 - 160 3 - 155 4 - 150 5 - 150 6 - 160 Engine start and drive: Compression test:

Working on my 93 resurrection project. The truck sat in the woods for 4 years and I now have it running and stopping, however when you put the shifter in D, the truck is starting off in either 3rd or 4th gear. If I shift to 2, it'll start in second. Shift to 1, starts in first. You can...

I've been getting A/T temp lights. 1st time was shortly after my timing belt was done. I pulled over & found the Rad reservoir was empty. Let it idle as manual says to do for temp lite, added coolant & waited for light to go out. Continued on to an off-road trip and no issues. Few weeks later...

Hello, I am selling my 1997 1FZ-FE engine with its transmission. The engine and tranny have 267K mile sand the head gasket was done at 239k. I am selling the engine because I have swapped in a diesel. The 1FZ-FE engine was fully repaired along with some nice add ons such as honed throttle body...

This is the adapter by Jerry Nichols of Colorado Offroad Express and built by Advance Adapters. Will bolt a NP203 low gearbox to a TLC 19 spline transfer case. Been sitting in the garage for longer than I care to say. Moving out of country and so I'll never use it. Hope someone else can. $150 +...

Everything was going fine until I was getting ready to actually separate the damn thing from the transmission and it would not let go. Took an hour of working around the edges with a pry bar just to get it where it’s at in the picture. Tcase is secured to the jack and about level with the...