plate

I need a 1973 fj40 u bolt spring plate. One of mine is bent. It could probably be heated and straightened. I would like to see if I can find one reasonably priced. Thanks.

Thanks!! Backing Plate has been found. Jeff

Trying to price out the following part, and not seeing anything online to help. It's the insulation piece that attaches just above the muffler, below the right second row. Any help on pricing this item would be greatly appreciated! There's no rust (just a little caked on mud that could come off...

I'm not sure what this part is called but the license plate bolts to it then it is attached to the drop gate. The reverse lights are also attached to it. Mine has broken connectors and is a rattle trap. I put some small felt pads in the gaps to keep the racket down but I'd like to know what...

Probably like a Unicorn- but you guys come through all the time. I need a 1983/84 Radio Delete Plate for the newer dash on the 83/84.

i had thought the license plate bulbs were out on the new to me 81 BJ42 i am fixing up so when I took the plate holder off to refurbish and paint, I replaced the bulbs, yeah they were toast but no. new ones didn't fix it got underneath to look at the wiring and lo and behold the wires that...

Searching for a good condition Timing gear cover and backing plate and oil squirt-er from a late 2F years 85-87 out of a FJ60. Also need thrust plate and bolts, and possibly more if you're parting one ... Anyone parting out a late 2F ? Thanks. :)

Just looking for the stock skid plate. Someone has to have one laying around they don't need. Let me know how much you want for it. Thanks, Scott

Can someone with more neurons than me walk me through to figure out how to trouble shoot license plate and dome lights not working?? My blinkers, parking and reverse lights work.

Anyone used torque plates on bore or hone jobs for their engine? Did you use aluminum or steel plate and what are your thoughts? Did you take multiple before and after bore measurements, and if so, how did it turn out? I am doing a diagnostic teardown and blueprint job. 1FZ engine building and...

Looking for one close to Denver if possible. Let me know what you have. Doesn't have to be showroom quality. Thanks, Scott

Used FJ40 polished aluminum diamond plate quarter panels. Good condition. $100 plus shipping.

Swapping the 3-speed for a 4-speed in my FJ40. Want to also swap the glove box shift place for the one that matches the new trans. Anyone have one?

Trying all over to buy the above for my cruiser but having big problems. Decided to fabricate one here in Kenya. Can anyone point me to a diagram for the oil flow that I can give to one of the engineers here? Cheers Mike

So I had the same problem as many of us to with the little plastic retaining nuts breaking and no longer holding the sill plate steps on their studs. Since these studs are some strange metric thread pitch it is hard to find something to replace the plastic nuts with.. Here is what I came up with...

I intend to remove the unleaded restrictor plate from the fuel fill neck of the 60. I did this way back when with the 40. The 40 was easy - a few light whacks on the plate with a flat punch and hammer and the spot welds popped loose. Tried the same technique with the 60 and no joy. I'm...

Hey AZ Cruisers... We've moved to the great white north, that is Show Low AZ, and are lovin' it. Part of the perks of being up north is no emission testing and I can get a 5-year tag too! For my 96 FZJ80 the cost is a whopping $79 for a 5 year tag. I was looking at AZ personal plate...

in need of a pressure plate for my 2lte bought a automatic motor trans combo went to put it in my old 2L truck and the plate off my old one is only 6 bolts please let me know if you have one laying around 801-564-9029 Ryan

I am trying to put in a Carb for my '77 FJ40. But it is sitting too low. Looks like I need a Carburetor Insulator Plate / Heat Shield. Looking around the net I get conflicting years/months for a correct fit. Any Idea on what will fit my rig? Which parts cover my 01/77. (and maybe a good...

Looking for a good sm420 and adapter plate to 4 speed bellhousing Thanks James 631 873 6912