heater

Im not sure if it works but everything I have worked on in this Pig has been fine. I don't need it. $100 plus shipping

So about every vehicle I have ever worked on with a 22r/re/rte has had jacked up water lines behind the head - See the picture below of the brass lines - they always leak some and look like junk. Since I have the head off my 4runner, I would like to fix them. I had an idea about using something...

Looking for the rear heater pipes (back section ) as well as the rear engine outlet pipe (pipe that the PHH goes to). Also looking for an engine mount cover (square box goes over engine mounts).

Looking for the rear heater pipes (back section ) as well as the rear engine outlet pipe (pipe that the PHH goes to). Also looking for an engine mount cover (square box goes over engine mounts).

Blew the heater valve.at 263k miles. It was not just brittle, it was toast. Zero integrity. Thought it was the PHH but that turned out to be fine. Replaced the pesky part since most of the fluid was already drained on my driveway. PHH took about 2 hours between cold ones and mucho forearm skin...

After reading through various threads I finally bypassed and removed the rear heater using the simplest procedure I could think of. Hopefully this thread can help someone else out that has been reading multiple threads on the topic. Please note that I did not drain or flush my system at this...

My Cruiser has years of French fries, coins, etc built up under the rear heater from the PO. I want to take apart the rear heater as much as possible save for the heater pipes. Sometimes I use it to dissipate heat. Has anyone done this, can I just start pulling things off until I get to the...

my circuit breaker relay keeps tripping out.....is that a stuffed fan motor most likely ?

Can someone suggest where to start to repair the leak.At first glance it appears as though I will have to pull the whole heater assembly apart .Is there a procedure or more simple answer.

I need a substitute for this part.

Hi mudders This morning I removed my PAIR system. I purchased the 1995 heater bypass hose but I forgot to get the gasket (see attached photo). Can the existing gasket be reused? If not does anyone have a P/N for a new gasket? Many thanks

Need whats pictured broken. Shipped to 34613. Thanks!

I replaced my heater T fittings the other day, however as I was replacing the first one, a small piece of the end on one of the T's broke, and I'm not sure if it went down another pipe. I tipped out as much fluid as I can to "wash it out" If it happened to have gotten in my system, 1- what's the...

This heater setup will not clear the shifter in my drivetrain swap, so I figured I would see if someone needs one before I chop it up. Early heater unit, knob intact, defroster flap moves freely. Light surface rust and dirt, easily cleaned up. Heater duct, reasonably good shape, someone has...

Hello everyone, I am a newbie to the site. I have a 95 fzj80 and am needing to put a new front heater core in it. It started out slow but now my floor board is soaked on passenger side. My question is can I get a factory Toyota core or is their a reliable after market?

Heater core TU (tango uniform) and having trouble finding the core. Will heater cores from non-japanese 80's work in HDJ81? Any help on finding a heater core or info on an alternative solution would be appreciated. Thanks, Rich Boyle

1978 FJ40 The lower portion of my heater blower unit (that bolts to the passenger side firewall) is broken and missing a good chunk where it meets the louvers on the cowl. My fan motor works fine, not sure if anyone would part with/sell just the housing? Of course Id like one that is not...

I'm really stuck right now: I bought the 35mm block heater, and I went for a (kinda-sorta) accessible freeze plug just aft of the injection pump on the driver's side. I tapped on the freeze plug, but it went into the block, and while I can wiggle it around with my finger, I can't get it out...

heater box is good but it's missing some parts. Comes with a heater core of unknown quality, I never had water in it so do not know if it leaks. Vent tubes are in ok, but not great shape. $50 plus the ride for all.

Someone please post photos of the correct location of lines & hardware (clamps and brackets, etc.) running from the firewall back to the rear heater for a 1980 FJ40. And the mounting location of the heater itself. I can't seem to find the mounting point. Thanks