fuel

Hello Folks! I've always had a temp gauge that sometimes like to peg itself out above hot, even though the truck is running fine. It will do it maybe once every 30 minutes, for 30 seconds or so. Not that big of a deal, but I noticed yesterday that the fuel gauge did the same thing (pegged...

I'm trying to "break"/loosen the 14mm bolt/line from the Filter itself (19mm). Its on there good, and with lots of other lines in the area, I'm afraid to put too much force and cause the wrench to slip, or even worse, damage one of the rubber lines running close by. I'm afraid to put a little...

New to me ‘72 55. Going through some immediate issues. Would love to have a functional gas gauge. I think I have read through maybe 20 threads on this issue. My float/sender is functioning properly (checked with ohm-meter) Contacts on the back of the gauge look clean, the ebrake and charge...

Seeing if anyone has one of these sitting around they want to part with. truck is a 2/76 PM me if you have one! thanks!

I seem to get about 2 years out of these pricey mech pumps. I think they can be rebuilt?? Anyone have kit info? I am currently stuck in Springer NM and the pump went out on me. I may have to rural engineer am elec pump inline????? I searched the FAQs but couldn't find much. I know a lot of...

(Toypta 3b)When I go to turn the key I can't hear fuel pump (like I usually can) and the engine is reluctant to start and will stop if im not giving any throttle. I tried to take the fuel filter thing off but am not sure how to take it off. Any ideas on either? Cheers

Making the jump between a Fuel Pump tube 77209-60160, the breather tube 95312-13028, fuel hose 95337-06009, clamps, and the tubes on the body. I think I have everything that I need to reconnect the new fuel and breather tubes from the body to the new lines. The one part that raises a...

I have a good condition fuel tank from a 97 80-series. Had two tanks and had both inspected, cleaned, and recoated and am keeping one, but don't need the other. Will start by asking $600 shipped but open to offers. I don't have anything but the tank.

This high capacity fuel tank came off my 1982 FJ60. It needs to be pressure tested and possibly welded up on one of the edges. Or, if you can weld, you can make another one based on this one. The dimensions are about 14" H x 34" W x 26"D. There is a 45 degree angle at the bottom rear of the...

I found a project 1991 FJ80 that was local and at a good enough price that I picked it up. The PO had purchased it as a project for him and his son to work on with the intent to use it for light offroading, but it seems that they only made it as far as buying new wheels and tires before the son...

Hi all, I’m new here! I have a 1991 Toyota Landcruiser 80 Series. Today while driving she sputtered, stalled, her automatic steering went, and she said “see ya” for about 2 minutes. I was able to get her started back up and get her home. All signs point to her fuel pump failing, I’m assuming. I...

Looking for a non pitted fuel hard line clamp upper and lower for late FJ40 1/79 to end & fj60 80 -87. 23841-61021 #1 upper 23842-61031 #2 lower

Looking for the two different fuel hardline brackets for an FJ40 circled in the photo. Located in Woodstock,Ga

Hey everyone, got a 2012 sequoia. I believe the fuel pump has crapped out on it. It is a flex fuel vehicle. What I am trying to find out is whether or not the FF vehicles us a different fuel pump than the regular ones. Can anyone help me with this? I'd like to get one ordered so I can ger her...

I’m currently working on 75 carb I recently picked up and installing the return line and wanted to know where the opposite end of the line rests where it mates to the soft line. Mine currently is right up against the battery and would like pictures so I know where I need to bend it if needed...

I hope this question doesn’t seem too stupid but I’m assuming this is an electronic fuel pump in front of my fuel filter? I installed a new carburetor and it ran like a top and all the sudden it won’t start. It doesn’t appear to get any gas to the carburetor. I’m gonna change the fuel filter...

I'm hoping to catch some more input by putting this in its own thread. Relating to my solid state regulator project, but this could also help with others who don't go with the upgrade once it's available. What I'm trying to do is figure a good point for baseline calibration of the fuel gauge...

Hi guys, Using @cruisermatt ‘s vent hose replacement kit and all has gone great with it. I’m chasing a gas smell on the cab issue so figured I’d search for a clogged vent line. All the hoses looked fine, but I stick a very thin screwdriver into one of the metal ports the lower vent hoses attach...

I took my LC on a long trip and while at idle for long periods of time (2 hours), the RPM's started getting a little rough. No lights, never stalled or ever close...but from a consistent 7-800RPM's at idle with AC, it would occasionally drop to 4-500 and jump right back up. It wasn't "rough"...

Good morning folks, In getting power to the fuel injectors on a 5.3 out of a 2000 Tahoe, I'd like to use the wire that formerly went to my coil on my 88 FJ62. Is this a good idea? Thanks for any advice.