frame

Is this a thing? can you rebuild seat frames to take out the slop? Anyone have recommendations to find someone who could do this in Utah? No, I haven't taken them apart to see where the slop is, yes I know thats probably a great first step. Its my daily driver and I need it for driving...

looking for a frame with title and both VIN plates for a project. Needs to be in southern California near 92583. it would help if it rolls but i guess i could drag it onto a trailer. thanks, db

This is a rectangular wire brush that can be trimmed to fit INSIDE an FJ40 frame. I bought two, used one to prep for paint and it worked great. This one is new and unused. $40 bucks for the brush and handle. Shipping extra.

Anyone done it? Was considering sleeving the frame with a 2.5 inch pipe and running the exhaust through that and using a hanger on both sides so it doesn't rattle. This would keep the exhaust over frame from heating up the floor.

PM me if you have two in decent shape.

Early 70s fj55 rolling chassis for sale. Location: Royston Ga, 30 min N. of Athens. Good frame, Complete axles, Fj60 wheels, driveshafts, steering gear, some brake lines, Springs, shackles etc. Front Bumper ends Price: $1000 obo I also have a tailgate gear/motor/window panel I'd sell

Early 70s fj55 rolling chassis for sale. Location Royston Ga, 30 min N. of Athens. Complete axles, fj60 wheels, driveshafts, steering gear, some brake lines, Springs, shackles etc. Front Bumper ends Price: $1000 obo

Took my trailer in yesterday to a local shop and found this on display... Used to be an 81 based on painted over frame stamp...

I have an 87 mini truck that has a rotted out frame. The rear passenger spring hanger ripped off the frame at an event two years back. I am looking at options, either reinforce the frame, or cutting off behind cab and splicing another frame. Has anyone grafted another vehicle frame to the rear...

I am looking for a frame plate set, preferably the 4x4labs one. Also looking for the steering shaft, u-joints and pass through/bulkhead joint. I'd also take a pitman arm that can be or is already reamed for 1-ton TRE. Please PM me if you have anything.

I am looking for a good set of rear frame support/braces. Attached is a photo of the supports if I did not describe them well enough. Let me know what you have. Thanks, Chad

For Information Only - Does not seem to apply to Land Cruisers. But I wonder if it's only a matter of time because the 200-series isn't quite old enough yet? It covers the frames on 2008 Tundras but not 2008 Land Cruisers....could that be because the LC is made in Japan unlike the Tundra...

I want to cut the frame and weld in the factory hitch like some have done. I'm worried about two things and I'd like to hear from folks that have done this. 1. When I cut the rear of the frame off, what's to keep the rails ainged? It seems like this procedure would instantly misalign the...

Hey all, I'm getting ready to mock-up reassemble my 283, H42, and 4-speed case w/ new transmission cover and Downey bellhousing to go back in the truck for alignment and test fitting of the new motor mounts I'll be welding in. The location of the front mounts is pretty well established here on...

I have read thru the archives about cutting/rotating the cross members in an early frame; even found a couple with removable cross members. I have installed a 1978 2F Engine, Four Speed Transmission, and Transfer Case in a 1972 Frame. I knew going in the fit between the parking brake drum and...

Hey folks, Title says it all. I'm about to pull trigger on new CAT and y-pipe for my over the frame rail exhaust job. I'm partial to a cat with a Y-pipe since I've read of the y-pipe failing and I know mine is not in good shape. One last validation from Mud before I drop the $350. MagnaFlow...

Hi Guys, Recently acquired a 1980 HJ45... knew that it had some frame issues but was hard to tell to what extent with the flat tires high grass/vegetation growing around it. Now have it home and have put some new tires the frame being worked on and higher on one side is more obvious. On a...

Can anyone tell me what these are on my 1967 FJ45 frame? This one is on the rear drivers (left) side. I'm thinking it's maybe an exhaust mount? This one is on the inside of drivers (left) side frame rail. I have no idea.

I saw this on Tor's Facebook page and I was blown away. I think this is probably the best Land Cruiser configuration IMO. But I am curious to see what others think of this build pros/cons? FB link here: Torfab - Timeline | Facebook Photo here...

Surely this issue been widely discussed, however I have been thinking of a solution to this problem. I think I came up with a revolutionary idea and before I share it to test I would like to collect all succesful methods available. The question is: Given a fully boxed section of the frame where...