fj40

Hi All, new to me fj40, rough running since purchase, needed choke pulled out almost fully to run her (but grateful that I got her to run at all). Changed and set points/plugs/condenser/coil/plug lines/vacuum pipes/flushed gas tank/new fuel filter. Still rough. Skimmed intake manifold, new...

Looking to move an FJ40 hood. Please send a message if you’re headed that way! Thank you!

Meet "Rusty"! I picked up this red 78 USA FJ40 and drove it back to Atlanta from Chattanooga today. 100 miles doing 65 mph smoothly the whole way. I will give a lot more details soon, but the short story is I just plan to put new quarter panels on it, paint it and drive the wheels off of it. It...

Just getting back to cruiser stuff after some life issues. My son has his 74 FJ40 and has been working on it. Finally able to go for a ride. Here's the problem. He is having difficulty with the gas pedal height. I can barely reach it with my size 14 boot. He's tried putting his foot partially...

On my 1974 FJ40 I have the location for the Jack and rods. Where did the handle and lug wrench stow?

$37 shipped includes new OEM rubber stopper pad.

Hi, I am new here. I am trying to figure out what these wires and connectors are for, and what do I connect them to on a 1983 Toyota FJ40. I am asking about the connector on my hand, not the one for the washer fluid pump. I removed the washer and the radiator tanks to take this picture...

I'm doing an alternator conversion to a Chevy alternator on a '75 FJ40. Original Toyota alternator was using a 17mm wide (approx. 5/8") V-belt. Chevy alternator pulley is sized for a 3/8 V-belt. Where would I find a wide pulley for a Chevy alternator? I thought about using the pulley from...

Looking at FJ40's lately. Been scrolling through the build and tech threads to try to gain some knowledge. Just in the last month, reading through some threads, I'm already noticing things on some online listings which I had no idea about before I found this site. My price point is pretty...

Pulled from a 1965 many, MANY years ago. This core has the dimpled top tank and wrap around mounting bracket common to the early rigs. The inlet and outlet will obviously need to be replaced. My local radiator guy has never had a problem doing that. $100 for the core. $100 for the core support...

=========== NOTE - These are not mine, contact the seller via the Craigslist Ad ================= https://portland.craigslist.org/yam/cto/d/sheridan-1966-toyota-fj40-land-cruiser/7680784623.html 1966 Toyota FJ 40 Landcruiser. Mostly original. The engine was replaced some time in the 70's...

I am looking for a Full Float rear end this would be for my 1977 FJ40, I don't need the diff. Prefer western US location. If anyone has one they would part with let me know. Thanks

I was sitting in my Cruiser letting it idle to warm it up. Long story, but I apparently had a fuel leak that ignited. The engine compartment is burned. All the wiring and everything rubber and plastic under the hood is gone. Damage inside the cab does not seem all that bad. The dash pad is...

Anyone have the little rubber disk bushings that screw into the tub above the rear axle? Just need one.

Hey all, see photo below of how my windshield is sitting in relation to my door these days. WS is not in place on the door at the moment, so I'm assuming this is all due to an old windshield gasket that isn't compressing fully? Dash screws are fully screwed in too.

If somebody has an extra floating around and can throw it in an envelope I’m willing to compensate :) pic to show the exact linkage courtesy of SOR. Zip code 99669. Thanks

I've been poking around Alibaba and noticing a lot of reproduction 40 parts, from past experience with Chinese suppliers (fidget spinners hahahah) I know quality can be questionable at best. Has anyone ever tried to source a steel 40 roof? I've seen one at a local shop here in Portland but...

Well, just bought this one. Worked when installed and now doesn’t 2 weeks later. ISO another to determine if it’s the switch or wiring. Validated that power goes to the switch, but doesn’t come back out to power the turn signals. Anyone have one of these laying around? Planning to take this one...

These are the last bits of parts i have from my fj40 that i wont be using. I can only assume everything is from a 65ish and 1F engine. i can take more pictures for those interested and i will ship parts. The wiring harness has a few splices and cuts but can only assume its all or mostly there...

Not mine, but here you go... There's some history on it if that helps. I nearly bought it for $7K from another gentleman in IA and the frame along with it that needed swapped. I should have done it, but I didn't. That's a mistake on my part. He swaps the frame and tries to sell it with...