fj40

I was sitting in my Cruiser letting it idle to warm it up. Long story, but I apparently had a fuel leak that ignited. The engine compartment is burned. All the wiring and everything rubber and plastic under the hood is gone. Damage inside the cab does not seem all that bad. The dash pad is...

Anyone have the little rubber disk bushings that screw into the tub above the rear axle? Just need one.

Hey all, see photo below of how my windshield is sitting in relation to my door these days. WS is not in place on the door at the moment, so I'm assuming this is all due to an old windshield gasket that isn't compressing fully? Dash screws are fully screwed in too.

If somebody has an extra floating around and can throw it in an envelope I’m willing to compensate :) pic to show the exact linkage courtesy of SOR. Zip code 99669. Thanks

I've been poking around Alibaba and noticing a lot of reproduction 40 parts, from past experience with Chinese suppliers (fidget spinners hahahah) I know quality can be questionable at best. Has anyone ever tried to source a steel 40 roof? I've seen one at a local shop here in Portland but...

Well, just bought this one. Worked when installed and now doesn’t 2 weeks later. ISO another to determine if it’s the switch or wiring. Validated that power goes to the switch, but doesn’t come back out to power the turn signals. Anyone have one of these laying around? Planning to take this one...

These are the last bits of parts i have from my fj40 that i wont be using. I can only assume everything is from a 65ish and 1F engine. i can take more pictures for those interested and i will ship parts. The wiring harness has a few splices and cuts but can only assume its all or mostly there...

Not mine, but here you go... There's some history on it if that helps. I nearly bought it for $7K from another gentleman in IA and the frame along with it that needed swapped. I should have done it, but I didn't. That's a mistake on my part. He swaps the frame and tries to sell it with...

Restored front seats out of my 80 FJ40. Sand blasted and POR-15, new foam where needed (surprisingly not much), new Cruiser Corps upholstery. Free local pickup near Tampa, FL. Shipping will be expensive, No way to calculate until destination is known. Thanks for looking.

Over the last couple of days I started the roof rehab. I’m actually pretty happy. The rain gutter trim isn’t totally rusted out and needs little repair work. The shell itself, that’s another story… Any advice on working on the shell? I’ve considered buying one of the bathtub refinishing kits...

Finally installed the cable and pedal to match the Weber carb. Original carb and cleaner set up were long gone when i picked her up in 2009. Had a small Carter on there. Throttle had to push/pull rods and linkages and so was a lot of slop in gas pedal. Enough to make it very difficult to...

Hello all — I am looking for an early front heater for my 67 FJ40. Anyone have one sitting on a shelf? Thanks—

For sale Powertrax rear locker for 68-98 Land Cruiser 9.5 inch semi floating axle. Part number 9220883005. This was installed in the rear of my FJ 60 for just a few months before I came across a set of thirds with lower gears and an ARB. It is in like new condition with no rust or damage. These...

I began the process of rebuilding my heater box, and it wasn't until I began putting it back together that I realized I was missing a part. Im missing the L-shaped Linkage that goes on the driver's side bottom front. Ive been advised that there may be different styles of this part. Seeing as...

I always get a lot out of these forums so I’m finally trying to give a little back. Here’s some pictures of the rust spots we tackled last year.

Since moving my fuel tank under my 40, I’m left with a space under my passenger seat. To keep it period correct, I want to install a drivers side tool box on the passenger side. I’m looking for the tool box, lid, seat mount, and latches.

$1000 picked up in East San Diego (Alpine)

1976 toyota fj40 for sale by owner - Uniontown, WA - craigslist - https://lewiston.craigslist.org/cto/d/uniontown-toyota-fj/7679920085.html This is a project that I acquired. Its on one ton axles Dana 60 front with a full Detroit locker and in the rear a spooled 14 bolt. The motor has been...

Looking at different headlights for our build. I keep reading about these lights - Toyota (81110-60P70). I know nothing about these lights. Will these be plug-and-play with the wiring in our FJ or ???

=========== NOTE - These are not mine, contact the seller via the Craigslist Ad ================= https://phoenix.craigslist.org/evl/cto/d/white-mountain-lake-1971-toyota-fj40/7679814257.html $43k invested. Frame off restomod just completed with a rebuilt 350 V8 with Sniper fuel injection...