engine

I know someone has this and surely isn't going to use it. I need an oil pump and a cam for an h engine. Let me know what ya have. Thanks.

Hello I am procuring an FJ40 and two 1F engines. One is a SOR rebuilt engine, and the other is the old one with 60k miles that needs some lower end work, but works. I am looking to sell/trade both these 1F engines for a rebuilt 2F. 1f engine by Matt1260 posted Feb 5, 2017 at 6:58 PM1F engine...

The previous owner painted the truck, and it looks like they painted over pretty much all of the seams. Painted seam by Aaroneous posted Feb 5, 2017 at 12:01 PM I need to pull the engine and replace it, and everything I've read shows folding down the front grill. I don't see any way of doing...

I am thinking about installing flood LED lights when my nudge bar arrives. I cannot find it, but I am sure with all mods done on this forum it is an easy answer. BTW I have the 16LC. How and where in engine bay do I lead wires through firewall inside the cabin to install the switch?

Did a pretty complete half way through winter clean up on the interior on my '13 LC. Found a block heater (Kat's 11813) shoved down under the door to the jack. The heater is designed to be placed in a hole (~5/8" diameter by ~4 inches deep) in the block itself...i.e., it's not a water jacket...

Hello all, I'm working on my vortec swap and had planned on taking a video of the stock tach for a 0-60 or 80 run.. then another after the swap to show the difference in split screen. But.. I forgot to get the video from stock config, and now the engine is out and sitting on the ground. So...

Selling my 1988 FJ62. Very clean inside and out. No rust. 277K on the truck. Engine rebuilt at 268k. Bumpers and wheels are plasi-dip black and can be restored to original chrome. Black roof is a vinyl wrap that can also be removed. Original paint on roof is in good shape with the exception of...

All: I'm hoping that all you guys or gals might share some knowledge on this topic.. I have a 2k LC, 215k miles. Engine runs smoothly, but has what I suspect to be a bearing noise coming from one of the pulleys in the front. So my question basically is, how does one locate the correct...

Just finished replacing the head gasket. It just won't start. Here is what I have tried so far, and the results: -Re-did the procedure for installing the distributor. -Took off distributor cap, set crank to top dead center, and verified distributor rotor is pointing in correct orientation...

Hey guys I was going to hang on to my engine and trani, but I think I'm gonna go ahead and sale them to fund the rest of the project. Runs great has a Motorcraft carb, on it and headers otherwise looks stock. I can send a video of it running. Tranni works as it should, it will need a clutch. I'm...

Hi everyone - relatively new owner of a 2001 LX 270. Recently notice an intermittent clicking noise that lasts for about 5 seconds and sounds like something cutting on and off. Noise seems to be coming from engine compartment on drivers side behind the steering wheel. Here's a video where I...

So, I've really been focused on 2006-2007 LCs because 230 (or 235) hp vs 275 hp is about a 20% boost. That's pretty significant. But is also VERY limiting in terms of available vehicles during my searching, and most will have other "features" I'd rather not have (NAV and AHC). So, is it possible...

Hello Mudders, I have a situation I would appreciate the help of those who know with. I have a brown 1983 FJ60 I bought some months ago with a bad engine, it has a chunk out of the block due to coolant being added while it was hot. That's the story I was told at the time and I have no reason to...

I have the Toyota factory oem engine repair shop manual in new condition for sale. It covers B,3B,11B, 13B and 13 B-T diesel engines. It includes sections on Engine mechanical, Fuel system, Cooling system, Lubrication, Starting system, Charging system, and Specifications. Its the step by step...

greetings. I have this B engine 11411-56020 with a broken oil pump. I am tryng to find the spare part but here in Costa Rica it is almost impossible to find that part and neither on the internet, there I found a very look alike but don´t know if it will fit... By logic I need an 11301-56020...

Hey All - Newbie here, I have been on the site and enjoyed it. First post but its a big one for me I need to ask for help/advice. I purchased a 2004 Cruiser 2.5 years ago with about 88,000 miles. Most of the service records came with it, with timing belt service being done shortly before I...

i may be going crazy but ...... im installing a 87 2F into my 77 FJ40 for the life of me i cannot figure out where the rear engine mounts actually atach to the engine are they different everything i have read said this engine bolts right in many posts on that here on mud see pictures

I've got the car in the garage with the axles broken down and the exhaust a little cut up due to the PO pulling the cats. Tonight I thought I would check compression and set valve clearances. Checked the FSM and both processes are based on a hot engine. Has anybody performed these with a cold...

Hello, This is my first time trying these forums. I am working on a 1976 stock fj40 and have a broken plastic engine fan blade and need to replace it. I am not sure if the fan clutch is good or not but am wondering if there are any fixed fans that will work? Also I think that it is a newer...

Hi, I'm looking at purchasing a local FJ60 that the owner says is in great condition, but I happened to notice it's missing a few hoses compared to some other photos I've seen in the engine compartment. I don't know these trucks well enough to know if that's something I should be concerned about...