cover

.

I'm looking for a original Warn 8274 winch cover. The older one that had the warn hub in the center of the W. I like the look of the older cover compared to the new ones you can buy now. Thanks Levi

I'm using @Cruiser Corps seat covers and picked up the rest at Oklahoma upholstery. Let me know any tips or tricks for the passenger seat. I'm working on my 1972 FJ.

Side cover with hardware off a FJ60 2F and matching big cap distributor. $125. Pm me if interested.

Im on the process of replacing the valve cover spark plug seals and I noticed I have scored the seal surface in a few areas. Should I be concerned? I forgot to take a picture before I dropped it off at the machine shop to get cleaned (im doing a head gasket) . I was thinking maybe a thin rtv...

This is a fj40 fuel tank cover. Been in the barn for a long time. Covered in dirt, however is in very good condition. No rust. Bolt flanges are all there in good shape. $80.00 Plus shipping

I am looking for a tan fuse cover right under the steering wheel. Shipped to VT. Thanks Matt.

Just getting some parts powder coated and wondered about the valve cover. Mine is a 69 F motor so the valve cover is black, or was once. Is powder coat a good idea? And should I do inside and outside or just outside? I have googled it and found some folk saying it can peel off the inside and...

I just bought a grab bar from Cruiser Parts and I am disappointed in the finish they used to dye the grey bars brown. It looks like they just spray painted it with gloss spray paint. I can't bring my self to poke holes in my dash to install it, as in my it opinion doesn't match. This got me...

Quick question all. Does anyone know a part number for the U shaped seal that sits on the flywheel inspection cover. Mine was brittle and totally fell apart while pulling it off to replace the clutch. Also, it appears that the rest of the sealing of the cover is just a generic rubber/foam tape...

I seem to have lost the door to my timing window (pic below). Is this a big deal? If so, any idea where I can find one? Thanks!

Hey guys. I'm working with the 100 series crew to do a run of tailgate covers. Since I'm also in the process of doing a drawer system for the 80, I figured we might as well do gate covers at the same time. Here is the original thread: Gauging interest in a new tailgate cover Here is the...

Looking for FJ60: Flywheel Cover / Bolts 1983 FJ60 Owner's Manual / Paperwork Thanks!

Fellow Mudders, I am in need of a wiper park switch cover for a 1972 FJ40 wiper motor. This is the snap on one not the one that screws down. I understand that they aren't just laying around all over the place, so I want to make my own. I will be casting this from urethane, so I can make as many...

I'm planning on installing an FJ60 distributor/coil/igniter in my '76 FJ40 and need a dented side cover from an FJ60 (or later FJ40).

Hi everyone, I had an oil leak at the front of the engine and I decided to change the crankcase pulley oil seal and oil pump cover o ring. See my crankcase pulley below, what do you guys make out of it? Can I still reuse it? The rubbery is pretty worn out. I also noticed a crack in the...

I am looking for the following parts, if you have any of these I would be really grateful if you could send me a PM with your price and the condition of the part. 1. Steering Column Cover 2. Driver´s Seat Belt Gray 3. Steering Wheel, has to be in good shape. Mine is ok but the rubber separated...

I think this came off a 2F bellhousing. $45 plus shipping.

Title says it all. $50 plus shipping.

84 fj60, original body mounts, 3fe head and valve cover. Incredible pita to get the valve cover off and am contemplating going back to the 2f one and/or shaving the lip on the firewall. I'd guess that because the 2f cap is designed to go on a taller engine it might fit better. Can Anybody with...