axle

Hi, Is there a way to separate the dust shield from the plate that bolts to the axle? There looks to be 4 or maybe 6 pins that hold the dust plate on. Maybe they can be pressed out than back in. I’m restoring a rusty 80 axle for my build and I want to get this part to clean up and paint/por15...

Hey all. I'm in need of a FJ40 bare front axle housing 1968-1975. Shoot me a PM if you can help. Thanks! JP

I've been procrastinating rebuilding my knuckles, now it appears my hand is forced as it looks like i've blown an inner axle seal. Hoping to maybe find a toyota mini truck axle to swap disc brakes at the same time. Is 1978-1985 the only years that are compatible? Thanks so much for your...

Hi All, I have a 97 LX450. I had the front axles rebuilt about 2 years ago but now I have a significant leak coming from the front passenger axle. I also verified the diff breather was clear per other forum posts. Any guidance on parts order(cruiserdan?) or tips/tricks/ things to be concerned...

$1500. 4.10 non locker, No shipping. Local pickup in Los Angeles area near San Gabriel, CA In car right now, engine/trans/tcase/driveshaft out of car. $150 discount if you remove it from the car. It includes the tie rod. I have an engine hoist available for loading it.

Looking for a 2010+ FJ 8.2 rear end for my GX470. Recently popped the stock GX rear and am looking to upgrade. Looking for either full axle assembly with e-locker third member included, a straight housing, or an 8.2 third member w/ e-locker (stock preferred, but ok if it’s regeared to either...

Up for grabs is the major KDSS components from a MY17 200-series. -Front KDSS Piston ($400+shipping) -Rear KDSS Piston ($400+shipping) -Accumulator ($500+shipping) -Adapter Fitting ($100+shipping) -Front KDSS Arm ($400+shipping) Will sell the whole package for $1500+shipping. System was...

Hey Mini truck guys. Can I bolt in an FJ80 front 3rd member into an 1984 mini front axle? Thanks

FOR SALE: $75.00 +S&H (OBO) Early Disc Birfield PN 43405-60013 $75.00 +S&H (OBO) Early Disc Long Axle Shaft PN 43412-60020 $75.00 +S&H (OBO) Pair of Early Disc Dealer Warn Hubs PM for details.

I’m building a disc brake axle for my 45. I’m piecing together 60 knuckles onto an axle tube from a ‘74 55. I had to grind the inside of the axle tube for the birfields to fit. All that’s done and I’m assembling the knuckles out. I discovered that when I install the hubs that there is no...

Hoping someone has a bent or otherwise damaged axle with one good spindle end. I have n axle with one bad end

Looking to purchase or borrow an inner axle seal driver from Wit's End, seems they're out of stock. I've got the inner axle seal out but noticed wear on where the birfield rides, hoping to hammer the seal in a tiny bit further in the housing. Any help is appreciated!

How do you measure bent rims or axles? What would be a limit? Picture is of one wheel measured at the outside edge of the wheel. Still chasing a vibration at around 65mph Bearings are good, but will probably check em again. Also drive shafts are balanced. Thanks

Trying to dial in your rear suspension height after a change in setup? Adjust for weight on one side vs the other? I used the smaller ones to adjust for gas tank/rear tire carrier lean. The 30mm spacers are about 1 - 1.25" lift. I am selling a group of spacers that are just for you! 2x 30mm...

Two sets of gears and install kits. I bought these gears over 10 years ago to put in my '78 FJ40 and they have sat on a self in the garage ever since. Moving out of country and need to sell. $500 + ride New price : $400 + shipping

Haven’t driven in a week. Came home to a small oil puddle nearby the DS rear tire. Looks like oil is dripping off of the rear control arm. I can’t really tell what’s leaking because of the oily undercoating. Before I start cleaning up a ton of oil, any ideas? AHC or Axle leak?

Pair of OME 2702 front springs. Nothing wrong with them. They have about 3500 miles of use. Great springs, just decided to go another route… $95

2004 LX470. Replaced my front axle bushings but still have an occasional clunk in the rear at stop and go at stoplight. Need advice on testing to find the culprit bushings.

Would like to trade like valued amount of some of the below items for: complete Oak 3rd row skins, plastics, and dog bones (mounting bar goes in floor); or OBO cash; paypal; or venmo. Pics are on Ebay listing or CL with link. Do these prices seem really high? Well they are- this ad is Or Best...

hello im new to the forum i have been collecting parts for a few years but need to clean out my space a bit i’m located in boulder city 89005 for sale is a set of 1 ton axles dana 60 front with factory 4.10 gearing. gm 14 bolt rear axle. both are original and un modified in hood working...