axle

I sold my landcruiser and have the following parts available to cleanout the garage. i have the following: 2 engine oil filters for 2LTE diesel engine. 1 fram and 1 baldwin #7029. there filter are $40 a piece retail. toyota part # 90915-03006. could work for 1hz and 1 hdt engine as well, pls...

In no terms do I classify myself as a mechanic, so excuse me if my analysis sounds silly, but let me get to the point. I recently did a few thousand mile round trip from Michigan to Moab, Utah, in my 1991 FJ80, during the trip after around 300-400 miles of daily travel there would be a noticable...

Rear axle from 1997 land cruiser in good condition. Rust free.$450 you have any questions text me 8326907656

Ok long story short I sold a jeep and bought a 97 40th anniversary Land Cruiser. Being new to Toyota I am having to learn as I go as I want to do the majority of the work my self and with it not being my DD it will be ok to stretch projects out over just the weekend. All that being said I got...

I haven't seen this topic anywhere, opinions please. I'm considering a Diamond up front on my 40, but at a 60 width. The question is: would it be alright to leave spring perches original instead of outboarding? It doesn't seem to me to be that big of a factor when we are only talking about 1 ½"...

FRONT Third member pulled from a 1994 landcruiser 80 series, 4.10 open, gear wear pattern looks excellent! Also have inner axle shafts and outer birfields(without tone-rings for "ABS"), knuckles, spindles, steering arms, drive flanges, rotors. LOCATED IN GREENWOOD, SC, USA. High Pinion third...

Sold - Complete set of Ball and Claw axle shafts for a Pre 1968 FJ40 The shafts are in excellent condition, no abnormal wear, burrs, or scoring, they are coarse spline. These were in the truck when I got it and were either recently replaced or are in great OEM condition. $100 plus shipping...

How common are semi floating rear axles here in the states, I just picked up an fj60 with a semi floating rear axle but I see so many of them with full floaters. Basically my concern is if its the original axle or the previous owner took the full floater from my 60 and slapped on a semi. I will...

I am in a group and we have an old 32' travel trailer frame with 2 rear axles. We have built a parade float on it and paraded with 16 people with out any issues. Our group is growing and we are going to added 3 new rear axles this year and would like to add a front axle that is steerable by...

When I was near work this morning, I started smelling burning oil. Foul smelling burning oil. I was pretty sure it wasn't coming from the engine. The question is, is this safe to drive home without damaging the DIFF? Not sure how much oil is left in there. I need to go 25 miles.

Hi everyone, I'm new to FJ62 ownership first post here! :) I'm doing a front axle rebuild and am trying to get the freshly cleaned and repacked drivers side birfield back on its axle, but can't compress the snap-ring to get it in. I've tried using a hose clamp, and even a zip-tie to compress...

Is it possible to remove the oil seal on a Non-ADD Differential and bolt up an ADD axle tube? By removing the seal, the tube and ADD system gets oiled. The only difference I see is that with the ADD system you get needle bearings, and the Non-ADD diff only has the machined in "bushing" with oil...

I've searched but can't find a solid answer... If this has been covered please point me in the right direction... I have a 71 and the rear diff is welded. (bought this way). I drive it 75% on road, and 25% on logging roads. It works great, but I'm tired of the squealing and tough to turn corners...

Hello, im loking for a Toyota FF rear axle for my Toyota FJ73, I currently have the Semi float and want the full for a Locker conversion. thank you!

Both CV Axles are bad on my 2009 GX 470. I picked up two 43430-60061 assemblies and have blocked out a morning this week to do both sides. My bearings are also bad so on Sunday morning I contacted Andy at bluepitbearings.com to order two of the KOYO bearing and hub assemblies. He told me they...

Toyota SST "Steering Knuckle Centering Gauge" (number 09628-60014). $350 I purchased this used off ebay a couple months ago to complete a disc brake conversion on my FJ40. I used it once for both sides. As you would expect it has seen very little use and is in excellent condition. I will even...

For Sale Toyota SST "Steering Knuckle Centering Gauge" (number 09628-60014). I purchased this off ebay a couple months ago to complete a disc brake conversion on my FJ40. I used it once for both sides, and now I can "pass it along" to the next person who needs it. As you would expect it has...

For a 1970 FJ55 drum to disc brake conversion. Specifically looking for knuckle, brake backing plate, birfield outers, spindle, steering arms, and locking hubs. I live in southern California-any leads greatly appreciated.

OK, under the LC today to change engine oil and filter and having a general look around, my attention is once again drawn to rust caused pitting on the swivel balls. Not leaking as per oil contaminated, just the fact that as you turn the pitting picks up grease and brings it outside the seal...