3fe

Are any 3F engine parts compatible with the 3FE? What about FJ62 interior stuff, like blower resistors? Does any of that work with a FJ80?

Hello everyone I have a 2F engine block that has been professionally cleaned and fluxed. No issues with it at all, only some light rust gouges in one cylinder that should come out with an overbore. I also have the head from this 2F as well, but it has not been cleaned. I have most accessories...

I have an engine and transmission from a 1996 Toyota Land Cruiser, same as Lexus LX450. Engine had 230k miles when removed from wrecked cruiser for a project. Engine was running when pulled. Asking $1000 obo. Engine and trans together Willing to split and sell separately as well Engine...

I have 92 FJ80, and on last long highway drive I had an intermittent problem with the engine 'missing' in firing, at around 65MPH and 2300rpm. If I backed off on accelerate and went slower after a short while it cleared. Initially I thought a fuel supply issue at the higher RPM so changed...

I have a 1984 FJ60 and recently installed a fuel injection system from a 1988 Fj62 into it. everything with the computer seems to be working properly and no codes are showing. We installed a fuel pump (MSD) by the fuel tank and it's pumping out 70psi at the engine bay. The fuel stops at the fuel...

Packed up this morning in Frisco, planned on heading out to do some wheeling for the day in my '91 FJ80, cranks and cranks, doesn't fire. Definitely seems like fuel delivery. Before we left Ft. Collins on Sunday, I dumped some fuel system cleaner in the full tank. I imagine I broke up enough...

My 1992 fj80 started idling very rough whenever in gear, to the point where I thought it was constantly going to stall when stopped at the stoplight. Figured I had a vacuum leak, and sure enough the pipe near the check valve of the air manifold was rusted and snapped in two. I pulled air pump...

Came out of an LX450. Purchased in 2005 from a gentleman that performed a diesel swap. Still crated & on pallet. I had plans for it, but have never followed through. Friend's son just diagnosed w/ cancer & will not live long. I am selling this motor to add to his fundraising. Includes gearbox...

I've spent some days searching and troubleshooting and need some help with ideas for what could be wrong and how to check. I'm getting a bit desperate for something else to even check. Rig Details Owned for 3 years 1992 FJ80 3fe Engine swap 30K miles ago (previous owner ran w/ out oil) ~150K...

hey guys i've seen and heard about putting the dual 3fe manifold on a carb'd 2f head but i havent been able to find any real info on how to do it or what you would need besides the mani's can anyone point me in the direction of build threads with details about the conversion?

The PO removed the cats and butchered the downpipes, so in order to install new O2 sensors and have a proper exhaust system put on, I need to find replacement downpipes. Exhaust shop said it would be cheaper for me to find replacements, rather than having them fabricate a set with the O2 bungs...

Hi There, I am the second owner of my 1988 FJ62. My uncle and I began converting it to a diesel with a Toyota 2H engine two years ago. This is a running project and I am selling as is. I would have loved to finisedh but life is going in a different direction. The interior is in good...

The water pump on my '92 (175k miles) finally gave out, so I'm replacing the thermostat while I'm in there. Thanks to @beno for the parts, super-fast shipping, and helpful advice on the project. The FSM says that the 4 bolts that hold the thermostat housing together need to be 13 ft-lbs, but...

The Patient: 1992 FJ80 3-FE 302K I started a new thread since the previous one I have been working on is so much different than the new symptoms. A brief history, after a failed distributor situation, I had the head gasket replaced and completed an engine "refresh". Engine has not been running...

My question for all you FJ80 & 3FE enthusiasts is, what would you include in a must have spare parts kit in your rig, thinking extended road trip around USA and down through South America? What are the showstopper components that I should have on hand?

I have a spare 3FE head that I just brought into a local machine shop to be cleaned and evaluated, and was told that it needs pretty much everything replaced, including rotators and valves. It is a good head though, no cracks and minimal warpage. They said it would cost around $900 to get it...

My cruiser gets sluggish in the heat, especially towards 30 C (90 F). It seems to have a harder time accelerating, even though it runs at the same RPM to maintain speed. Temperature gauge holds steady, too, and all fluid levels appear to be good. I've also noticed it has a harder time...

3fe valve cover in good condition for sale $40

never thought I would say this, but the time has come to sell my "baby" my 1992 FJ80 that I have built basically from the ground up. My build thread is on the 80 forum, and here's a link to the CL add. $6,000 mud price. Check my build thread in the 80 forum for full documentation. 1992...

3FE-Complete, pulled from a running FJ62-From Salt Lake City Utah. Will ship - buyer responsible for shipping costs. I also have wiring harness and ecu I will throw in. DM if you want pics. Thanks.