2f

I have a good 2F Engine with 4 speed and tranfer case from a 1975 FJ55. I ended up donating the truck to Wild animal part for new Lion Habitate - excellent final resting place for FJ55. the engine was running when I pulled it out. i am selling because I have nothing to put it in so I find it...

I am selling the 1976-dates carb that came on my ‘75. It was starting easily and idling well, bud developed an off-idle stumble during initial acceleration. I think this is due to a couple things: 1. PO didn’t have fuel filter installed and there was some junk at the bottom of the fuel tank...

I am pulling the 3FE from my '89 FJ62. It is all original as much as I can tell. It does have some leaks. 310K original miles, again as far as I can tell. Trans was rebuilt by PO and has ~1,500 miles on it. Comes with ECU, harness etc up to the transfer case. That is staying with the new motor...

Currently struggling to find anything available via the good ol internet or word of mouth. Help me get this thing back on the road!!

I am selling a 2F Remanufactured (Reman) Long block: Powertrain Direct description, “TOYOTA 2F COMP ENGINE 81-87. 4230CC. WITH AIR. WITH POWER STEERING. 8 BOLTS TOTAL FOR INTAKE & EXHAUST”. Long story short, I purchased an 85 Landy out of Billings MT two years ago, the cruiser had about 2k...

I have a 2F and 4 speed transmission out of a 78 FJ40 on craigslist. 2F was running when pulled and includes all accessories. I'm located east of Pittsburgh. Thought someone on here may be interested. Thanks for looking. FJ40 Landcruiser - Toyota 2F Engine and Transmission

2f bolts?? by Rkbaseball posted Jul 27, 2017 at 10:00 PM Does anyone know what the bolts on the heads above the exhaust manifold are for? There is one bolt for each cylinder and they are directly above each exhaust port. They are circled in red Thanks!!

I purchased these two cylinder heads in a collection & and would like to part them out. Please PM me with inquiries about what you see here. Full Disclosure, I know very little about cylinder heads etc. The link below ( hopefully ) should have photos of both heads for sale: RUGGED REFINEMENT...

I'm at the end of my path for a this 2F. It's as tuned up as I can think to make it: -289,000 mile original shortblock. 130 psi average compression. Fresh cylinder head and valve adjustment. No leaks from intake or exhaust. Almost completely desmogged. -2.25" catless to a factory sized...

I am looking for a clean Toyota FJ40 must have a 2f. Am in Western Colorado and yes I have the cash. Not a tire kicker. Scott Fasken 970-210-7321

Here is what happened... It's unfortunately a bit of an 'I told ME so'. It was time for an oil change on my 78 with a stock 2F. I was debating if I should try to clean up the crank case a bit with sea foam or B-12. I was leaning toward no, but then decided to do it. I used less than...

Not interested in building a 2FE or doing a 3FE or other swap. I'd like to add FI to my 2f with the primary goal being to not stall out on steep inclines while wheeling (as I just did WAY too often in Moab). I don't care about street performance, horse power, fuel economy etc etc. It just needs...

86 FJ 60 Engine 2F Complete engine assy With 4 speed trans Just pulled this out for diesel conversion, de smogged, Webber carb, 6 in to one header , distributer , igniter, flywheel, clutch At least a 100,000 mile engine. Even compression @ 125 psi, no noises oil changed religiously at 4000...

Hi All - selling our project and getting something safer as a daily driver for mom and baby. Ad and description here: Toyota Land Cruiser FJ40 Asking 35.9. Unfortunately, the creation price was far above that! Any questions, feel free to message or give me a call via the number on the ad.

Hi, Looking for a strong running 1.5F or 2F for sale. Up to 200 miles from 06830 (Greenwich, CT) Thanks

Did not end up needing in my build. $50 shipped CONUS

Reassembling my 2F and went to install freshly machined crank tonight and crank hung up on thrust bearing (#3). New crank is from a '79 2F and is .030" over. Old crank was .020" over. Block is 11/75. I bought .030" main bearings from SOR that are for 9/73-10/84. Old thrust bearings (upper...

Need complete bottom and intake neck, I have a top. Surface rust ok. Pm me

QUIZ FOR THE MUD-WISE 2F GURRUS This is my second post with these questions. I’m hoping that more will chime in. THANKS to everyone who helped with the 11 connections. There are a couple of the connections where no advice was offered and one or two that need some clarification. The good news is...

Longshot: Anybody have a 2F timing cover gasket laying around? I ordered one Monday but it won't be here for the weekend and was hoping to finish off a project. Would need to be triangle area. :beer: Ramon