What did you do with your 60 this weekend?

[micruz60]

On the (new to me) 62: Tore out the dysfunctional wiring the PO had installed to control a winch, which had been cut into the stock front bumper :geez:
Removed the deadfoot on the driver's floorboard, lol, found about a half inch of fine volcanic silt, cleared that.
Reconditioned the rear stop/turn lamp assemblies.

 

[BlackCat]

Kartchner Cavern State Park for a hike and swim. Then lunch on the tailgate while we took in the view.

 

[TRAIL TAILOR]

Finished up the 60 rear antenna/LED pod mounts and got to do a final test fit.

J

 

[Beams37]

No pics at the moment ... But made some good progress on my DIY drawer in the cargo area.

 

[cruisermatt]

FZJ80 front rotors/calipers, 100 series pads installed

 

[4Cruisers]

Kartchner Cavern State Park for a hike and swim. Then lunch on the tailgate while we took in the view.

View attachment 1941136

View attachment 1941137

View attachment 1941138

View attachment 1941140

Which half of the caverns did you do? We did one of the tours a few years ago and want to get back to see the rest.

 

[87CRUSR]

FZJ80 front rotors/calipers, 100 series pads installed..

How did the install go?

 

[BaileyCatDaddy]

I went searching for a new fun road. Found one but it is way too short, but it dead ended at a beautiful view.
I made it 99% of the way back to the main road without mud, the last hole I took a slightly different line and covered the front of the 60 in one shot.

 

[cruisermatt]

How did the install go?

Only took seven weeks. Not too bad

 

[BlackCat]

Which half of the caverns did you do? We did one of the tours a few years ago and want to get back to see the rest.

We didn’t do any of them. I’m not a fan of “guided” anything. We just went and hiked about 4 miles on the various trails for some exercise.

 

[Seth_O]

FZJ80 front rotors/calipers, 100 series pads installed

View attachment 1941291
View attachment 1941292View attachment 1941293

Are you using 80 series calipers with these?

 

[HemiAlex]

I drove mine to get tacos.

 

[NeverGiveUpYota]

Glad I have that to look forward to.... Any advice now that their done? I'm thinking start with penetrating oil now. Planning April/May time frame.

Go straight to a cutting wheel. Don’t waste your time w/ heat.

 

[NeverGiveUpYota]

The bad news: the door chime works now.

Easy enough to unplug. Behind the passenger foot panel.

 

[cps432]

Easy enough to unplug. Behind the passenger foot panel.

We have one in the 60 as well?

 

[Big Timber]

I bought a 1990 FJ62 in Cincinatti and drove it 1500 miles to Wyoming.

 

[NeverGiveUpYota]

We have one in the 60 as well?

It’s an annoyingly loud buzzer.

 

[cps432]

It’s an annoyingly loud buzzer.

Well I’m glad mine isn’t working.

 

[NeverGiveUpYota]

Well I’m glad mine isn’t working.

Plug it just for fun. It’ll only stay plugged for as long as it takes you to unplug it.

 

[Godwin]

I bought a 1990 FJ62 in Cincinatti and drove it 1500 miles to Wyoming.
View attachment 1941892
View attachment 1941894View attachment 1941893
View attachment 1941897
View attachment 1941896

Temp gauge is setting really low. May want to check the thermostat and upper o-ring.