Suspension Help!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

If that’s the case everyone else has bad springs except you and the OP!

Wrong. He cut the dead coil because he swapped to the heavy coils and didn't want stink bug when unloaded. Why does everything end with whining these days?
 
Wrong. He cut the dead coil because he swapped to the heavy coils and didn't want stink bug when unloaded. Why does everything end with whining these days?
I’m not whining my Dobinson springs are the correct height without hauling around 1500lbs of crap. :flipoff2:
 
@Lumpskie

For the record, I'm acutely aware of how a dual rate spring works (which is why I bought these to start with), and because it seems that I'm likely right on the edge of the transition into the second rate, I agree with the idea that we should be investigating the initial lighter rate portion of the spring.

We don't have any data for the initial rate, and I think that we can agree that the light rate portion (at least in my case with the 1014lbs experiment) is likely contributing very little to what information we do have (based on
your comment above regarding my coil pictures, and your math).
So let's go with the secondary rate data we've got.

If you want to break out the calculator, let’s do it...

The 1014lbs on the front of my truck is on the end of a lever arm that is 22" from the contact patch of the front tires (the fulcrum).
When you put weight there, by simple mechanics, it will remove weight (in this case 199.17lbs) from the other end of the lever (the distance from the fulcrum to the rear tire contact patch, or 112" for an 80 series) and transfer that weight to the fulcrum point (again, front tires, front springs).
If you're having trouble with this, it's the same reason the front of your truck raises up when you try to pull a bulldozer up onto your 16ft car hauler, only in that scenario the fulcrum is the rear tires instead of the front.

So now, you've got an extra 1213.17 lbs (1014 + 199.17) on the front axle. Now take that and divide by two because you've got two springs. 606.59... Now divide that by the distance traveled (2"), and we get.......
303.3 lbs/inch

Any inclusion of the light or transition rate portions of the spring into the calculation makes the numbers even worse for the heavy rate portion.

To visualize this, imagine that it only took 213 lbs to get through that first inch of travel (this is an exaggeration, for easy visualization), because the dead coils weren't in bind yet. It would then mean that it took the remaining 1000 lbs to go the next inch.
Which would make the heavy rate crazy high.
The point here, is that if our assumption that we've made it through the light rate of the spring and are only measuring the heavy rate is wrong, it can only serve to make the heavy section numbers appear lower than they may actually be, not higher.

So, I wonder; could whatever caused the heavy rate to be off (maybe one of those things I mentioned before, like alloy, heat treat, or temper) have caused the light rate to be off too?

Maybe that's why my truck is still taller than yours, even with five people standing on the front bumper...

You can tell me I don't understand how springs work. You can discount the math. You can tell me it's not applied properly. You can tell me I'm missing something.
The fact is, I've supplied enough information for anyone that wants to make an informed decision to do so. I also think this thread, without either of our input, has brought out enough of the demeanor and character of the other parties involved for someone to come to their own conclusions as well.


So, like I said before, you guys have fun, I'm out. :flipoff2:
 
This thread is basically dead, in a way thay everyone has wrote their peace...

What I have come up with is we have 2 people with a simular issue of getting 50mm/2" more lift than advetised & most previos customers reported like me.

25.25" +- fender measurment is a 5" lift. Granted one is measuring without a flare which then just minus .25" & lets give a error with a steady hand of .25" its still 24.75" fender measurerment which is 4.75" lift.

And then 1000lbs on front bumper is 23.5" is proff enough for me you have coils stronger/taller than mine or most.

If i remember correctly mine was 23.5" front & 23.75" heavy rear which all settled in @ .25" less.
When the other day after 2 years I'm at 23.25" front & with cut 7511 heavies is 23.25" +- .25"

I do have a 1" body lift so for the record all my measurent are 1' more then above specs.

The front 75mm coil are a 160#/ 260# with the 5th from top tranistioning.

There is a 50mm heavy option, but no full intermediate option. Im refering to there is no Slinky Long Travel 50mm intermediate rear that I know of. Slinky calls the 75mm 7501 intermediate coil a 50mm heavy coil.

I am very tempted to purchase the 70mm front 160/240# Patrol coils Woody has on his 80 that are 50mm lift & cutting my 7501 rear coils.
 
The front 75mm coil are a 160#/ 260# with the 5th from top tranistioning.


Yeah, if you look at peacesells pictures, it seems like he only has 3 coils with the lower rate. The wire diameter of the 4th coil looks bigger, like it's the transition coil. I was trying to help him get data on that, to supply him with the information he'd need to demonstrate an anomaly to Autocraft. But, as you see above, it seems like I was the only one interested in doing that. So, here we are.
 
This thread is basically dead, in a way thay everyone has wrote their peace...

What I have come up with is we have 2 people with a simular issue of getting 50mm/2" more lift than advetised & most previos customers reported like me.

25.25" +- fender measurment is a 5" lift. Granted one is measuring without a flare which then just minus .25" & lets give a error with a steady hand of .25" its still 24.75" fender measurerment which is 4.75" lift.

And then 1000lbs on front bumper is 23.5" is proff enough for me you have coils stronger/taller than mine or most.

Good summary. I'm no longer participating in the arguing BS, I wasted enough time already. Autocraft acts like 2 different people in PM's VS on the forum, and you don't get anywhere arguing with people like that.

I will post up more measurements when I have time to pull the springs. I worked 44 hours in the last 3 days, so I have not touched the truck.
 
Yeah, if you look at peacesells pictures, it seems like he only has 3 coils with the lower rate. The wire diameter of the 4th coil looks bigger, like it's the transition coil. I was trying to help him get data on that, to supply him with the information he'd need to demonstrate an anomaly to Autocraft. But, as you see above, it seems like I was the only one interested in doing that. So, here we are.

I'm still here, just might take a few days for me to get measurements. I appreciate the effort you and Greenbriar have put in so far and wont leave you hangin.
 
If i had time & know how i would get a press with a gauge & measure each inch all the way to fully compressed on these coils.. on video.
 
Been a way from this thread for a bit but I wanted to respond with a few thoughts. First off, @peacesells63 I don't know how you calculated how much lighter your truck is compared to mine. I've never provided any weight numbers so you're making calculations based on assumptions, and nothing factual. That seems to be one part of the problem in how you're coming to conclusions.

on another note about the communication with Darren that seems to have caused frustration.....from my own experience.....it is unrealistic for any customer to expect a vendor to spend time digging around a thread on forums to collect information related to a topic. I've been on both sides of this, as a vendor, I don't have time to go read through earlier comments to try and find information if I've requested it, and I don't waste my time doing that. If I had to do that with everyone that had a question I'd never get any work done. But I WILL request a customer send me the information directly through email or direct message. That way I have the information quickly accessible without having to wade through other people's comments and irrelevant information. If a customer responds to my request with "it's all posted in a thread on the forum", I'm not going to go wast my time finding it. Not because I'm not invested in helping the customer resolve the issue, but because there are 10,000 other things that also need attention. It is much easier for a customer to collect the relevant data and send it directly. This is exactly what Darren has done. I've been on the other side as a customer as well and understand it can be frustrating trying to solve an issue and it's taking longer than you want and communication is difficult. However, I have learned that for me to get the best help from a vendor I need to handle the communication somewhere other than on a forum, and I need to provide the vendor with ALL (and even more info than they need) so there is no way that I am making the resolution harder to find.

So just my two cents, and it's purely one guys opinion but I think @peacesells63 and @Greenbriar could change how they are communicating with Darren and have a much better experience. I have no doubt he's happy to work with you to resolve the issue. But again, also from a vendors point of view. If I were in Darren's position and had manufactured and sold literally thousands of these coils using a tried and true process that was consistently producing parts at the specs I have put in place and a customer were to contact me and tell me that the product they got from me was not within those specs and was wrong, my first reaction would be to question the legitimacy of that claim since years of production and thousands of parts produced does not support that happening. Could it happen, sure. And if it were me I'd want to know about it and verify it so that I could make whatever necessary changes with the tooling, or whatever else in the process to ensure that it didn't happen again. I'm sure Darren feels that same way since he's spent a lot of money and effort to produce some of the highest quality suspension parts on the market.

Lastly. I've never understood rejecting a product because I didn't like the interaction with a company representative. I get that those interactions can sometimes be extremely frustrating and put a bad taste in your mouth. I've been there, as I'm sure everyone else has. But in the end, if the product is the best thing to meet my needs, why would I short change myself by going with an inferior product? That only forces me to settle for something that may not do what I need it to as well and I'm stuck with that long after the frustration from a conversation has passed. Just an opinion and I get that everyone has their own way of looking at it. But personally, I've never understood that logic.

@peacesells63 or @Greenbriar if I can help with any information or actual data from my own truck with this setup, let me know. I'm happy to continue trying to help. Oh, forgot one thing. There was an earlier comment about the part numbers being the same between the intermediate and heavy springs. That is not correct. Maybe something got mislabeled. But through other conversations I've had with fellow Slinky customers as well as with Darren there are definitely different part numbers between the intermediate, heavy and extra heavy coils.
 
Been a way from this thread for a bit but I wanted to respond with a few thoughts. First off, @peacesells63 I don't know how you calculated how much lighter your truck is compared to mine. I've never provided any weight numbers so you're making calculations based on assumptions, and nothing factual. That seems to be one part of the problem in how you're coming to conclusions.

I didn't calculate anything based on your truck's weight. I made a rough calculation based on your height measurements vs mine and the stated spring rate. Also, I have not come to any conclusion other than the front end of my truck is too tall.

Lumpskie misunderstood my calculations in that post as well, as I applied 2 different linear rate calculations - one for removing the bumper and winch (180lbs), and one for adding 250lbs to the front bumper.

on another note about the communication with Darren that seems to have caused frustration.....from my own experience.....it is unrealistic for any customer to expect a vendor to spend time digging around a thread on forums to collect information related to a topic. I've been on both sides of this, as a vendor, I don't have time to go read through earlier comments to try and find information if I've requested it, and I don't waste my time doing that. If I had to do that with everyone that had a question I'd never get any work done. But I WILL request a customer send me the information directly through email or direct message. That way I have the information quickly accessible without having to wade through other people's comments and irrelevant information. If a customer responds to my request with "it's all posted in a thread on the forum", I'm not going to go wast my time finding it. Not because I'm not invested in helping the customer resolve the issue, but because there are 10,000 other things that also need attention. It is much easier for a customer to collect the relevant data and send it directly. This is exactly what Darren has done. I've been on the other side as a customer as well and understand it can be frustrating trying to solve an issue and it's taking longer than you want and communication is difficult. However, I have learned that for me to get the best help from a vendor I need to handle the communication somewhere other than on a forum, and I need to provide the vendor with ALL (and even more info than they need) so there is no way that I am making the resolution harder to find.

Keep in mind that you were not part of the PM conversation, so you are only seeing the responses that Autocraft has posted in this thread.

Autocraft had plenty of time to carry on a 2 hour PM conversation and add 5 posts to very the same thread he refuses to get my info from. This thread WAS full of relevant information before post #44.

I have 10,000 things on my plate as well, and a time frame to complete this truck so I can enjoy my vacation.

If you have ever posted a for sale ad on craigslist and received responses asking questions that could be answered by simply reading the ad, you know my frustrations on this subject. Like I said before, I sent him a link to the 2nd page of this thread and told him which posts to read. If I send an email, it would be a copy-paste of those posts.

So just my two cents, and it's purely one guys opinion but I think @peacesells63 and @Greenbriar could change how they are communicating with Darren and have a much better experience. I have no doubt he's happy to work with you to resolve the issue. But again, also from a vendors point of view. If I were in Darren's position and had manufactured and sold literally thousands of these coils using a tried and true process that was consistently producing parts at the specs I have put in place and a customer were to contact me and tell me that the product they got from me was not within those specs and was wrong, my first reaction would be to question the legitimacy of that claim since years of production and thousands of parts produced does not support that happening. Could it happen, sure. And if it were me I'd want to know about it and verify it so that I could make whatever necessary changes with the tooling, or whatever else in the process to ensure that it didn't happen again. I'm sure Darren feels that same way since he's spent a lot of money and effort to produce some of the highest quality suspension parts on the market.

A substantial part of my day job is reverse engineering proprietary products to improve designs. A good portion of the problems I see are deviations from specs during the manufacturing process and we not caught by QA, which seems possible in this case. I get paid to do this at work, I don't do it at home for free on my days off. I was definitely willing to help, but i'm not going to waste my time trying to change a guy's mind who said his springs are impervious to manufacturing issues, so my 1995 FZJ80 must be ~1000lbs light in the front end.

Lastly. I've never understood rejecting a product because I didn't like the interaction with a company representative. I get that those interactions can sometimes be extremely frustrating and put a bad taste in your mouth. I've been there, as I'm sure everyone else has. But in the end, if the product is the best thing to meet my needs, why would I short change myself by going with an inferior product? That only forces me to settle for something that may not do what I need it to as well and I'm stuck with that long after the frustration from a conversation has passed. Just an opinion and I get that everyone has their own way of looking at it. But personally, I've never understood that logic.

I definitely disagree with you there. If I don't like the way someone conducts business, I will no longer do business with them. That's just my philosophy, everyone else is free to do as they please. I also don't mind cutting the coil buckets off of my truck in favor of dual rate coilovers and air bumps. I could have finished that job in the time I have wrapped up in this mess.
 
@peacesells63 or @Greenbriar if I can help with any information or actual data from my own truck with this setup, let me know. I'm happy to continue trying to help. Oh, forgot one thing. There was an earlier comment about the part numbers being the same between the intermediate and heavy springs. That is not correct. Maybe something got mislabeled. But through other conversations I've had with fellow Slinky customers as well as with Darren there are definitely different part numbers between the intermediate, heavy and extra heavy coils.

I ordered (and received) 75mm heavy rears and 75mm intermediate fronts. From all of the research i've done on this forum, the heavy 75mm fj80 kit uses the same front spring part number as the intermediate.

Could you measure your heavy rate bar diameter?
 
I didn't calculate anything based on your truck's weight. I made a rough calculation based on your height measurements vs mine and the stated spring rate. Also, I have not come to any conclusion other than the front end of my truck is too tall.
I'm not trying to be argumentative with you, just sharing my opinion on the situation.

Doesn't matter at this point, just don't put too much stock in your calculations when you don't have my truck or Lumpskies on hand to get accurate data.


Keep in mind that you were not part of the PM conversation, so you are only seeing the responses that Autocraft has posted in this thread.

Autocraft had plenty of time to carry on a 2 hour PM conversation and add 5 posts to very the same thread he refuses to get my info from. This thread WAS full of relevant information before post #44.
You're correct, I wasn't part of the PM conversation and neither was anyone else reading this thread. I'm calling it like I see it based on what is visible here. Are you complaining that Darren spent 2 hours exchanging messages with you? Sounds like he was willing to spend time figuring it out.

I have 10,000 things on my plate as well, and a time frame to complete this truck so I can enjoy my vacation.

If you have ever posted a for sale ad on craigslist and received responses asking questions that could be answered by simply reading the ad, you know my frustrations on this subject. Like I said before, I sent him a link to the 2nd page of this thread and told him which posts to read. If I send an email, it would be a copy-paste of those posts.
We are all busy. Again, we have a difference in approach on how to handle the communication. I wouldn't expect a vendor to go read through a forum thread to find information even if I had sent him a link to a post. What's so difficult about a copy/paste? Sure it may seem unneccesary to you but as a vendor I can say that it would have been very helpful to me so that I had that information easily accessible in a direct communication with the customer, and not have to go poke around on a forum to find it later if I couldn't remember the exact details. That information would be good for my own records as well. Working with customers for years I can tell you I have requested information directly many times in the same way Darren did. Because it helps. So yeah we look at this point differently.

As far as enjoying your vacation, are the springs not working right now? Is the truck undriveable? I understand that you feel like the front is too tall and understandably want to fix it. But if the truck is driveable it's not something that will hold up your trip, correct? I'm sure if the springs need to get swapped out, it could still be done after your trip if it wasn't resolved beforehand. I guess what I'm saying is I wouldn't hold up a trip for this as long as the truck was driveable.


A substantial part of my day job is reverse engineering proprietary products to improve designs. A good portion of the problems I see are deviations from specs during the manufacturing process and we not caught by QA, which seems possible in this case. I get paid to do this at work, I don't do it at home for free on my days off. I was definitely willing to help, but i'm not going to waste my time trying to change a guy's mind who said his springs are impervious to manufacturing issues, so my 1995 FZJ80 must be ~1000lbs light in the front end.
I didn't see anywhere that Darren said it was impossible to have an out of spec spring that somehow slipped through QA or was mislabled, just that it was unlikely. I can still see where he's coming from with this because of years of producing these without issue and consistently within spec.


I definitely disagree with you there. If I don't like the way someone conducts business, I will no longer do business with them. That's just my philosophy, everyone else is free to do as they please. I also don't mind cutting the coil buckets off of my truck in favor of dual rate coilovers and air bumps. I could have finished that job in the time I have wrapped up in this mess.
We'll agree to disagree. I'm not talking about unethical business practices or outright stealing from someone. I wouldn't spend my money with a company that did those things either. We're talking about not liking the way someone communicates and not seeing eye to eye on an issue. Not the same thing in my mind. If it was, I'd have walked away from thousands of purchases, from haggling on cars, to heated discussions with the contractor that built my house. I agree, everyone is free to do as they please and if that's the stance you take for yourself, cool.

As to you last question in your last post, I will check the meaurement on my springs. I have to be honest though, you're comparing a truck with a stock front end, stock bumper etc. to a truck with a heavy steel bumper and winch, extra lights etc. Your truck is going to be taller without that extra weight. The picture you posted with your coworkers standing on the bumper, your measurements are pretty close to what mine were around the time I installed them. I've got 2 years of hard use on the springs now which is bound to make them settle slightly. And we're talking about roughly half an inch of difference between yours and mine with similar weight on the front. I'm not sure the issue is an issue? But I'm happy to help try to figure it out.

Also, the part numbers are not the same between intermediates and heavy springs. If they were how would anyone be able to tell what springs they had? The dealer couldn't be sure he was sending you the right thing if there was no difference in part number. What was the part number of your front springs? From my information the 75mm intermediates should be numbered 7501, the 75mm heavies are numbered 7511. If you have 7511, you were sent heavy springs not intermediates.
 
I'm not trying to be argumentative with you, just sharing my opinion on the situation.

Doesn't matter at this point, just don't put too much stock in your calculations when you don't have my truck or Lumpskies on hand to get accurate data.

I noted that my calculations were rough (based on a tape measure in my driveway) and the weigh of the front of your and lumpskie's truck was the variable being solved for in my equation - not a constant. No assumption was made.

I don't want to argue either - I like your truck and appreciate your response and willingness to help to try and help sort this out.

You're correct, I wasn't part of the PM conversation and neither was anyone else reading this thread. I'm calling it like I see it based on what is visible here. Are you complaining that Darren spent 2 hours exchanging messages with you? Sounds like he was willing to spend time figuring it out.

He spent 2 hours arguing and blaming me for his attitude. He could have spent that time working on the problem, but chose not to. I know you are some sort of brand spokesperson or something for slinky, so I don't expect you to join my side, but I would appreciate if this arguing would stop right here on an agree to disagree basis. Its over with, Kevin at EHO solved my problem.

We are all busy. Again, we have a difference in approach on how to handle the communication. I wouldn't expect a vendor to go read through a forum thread to find information even if I had sent him a link to a post. What's so difficult about a copy/paste? Sure it may seem unneccesary to you but as a vendor I can say that it would have been very helpful to me so that I had that information easily accessible in a direct communication with the customer, and not have to go poke around on a forum to find it later if I couldn't remember the exact details. That information would be good for my own records as well. Working with customers for years I can tell you I have requested information directly many times in the same way Darren did. Because it helps. So yeah we look at this point differently.

As far as enjoying your vacation, are the springs not working right now? Is the truck undriveable? I understand that you feel like the front is too tall and understandably want to fix it. But if the truck is driveable it's not something that will hold up your trip, correct? I'm sure if the springs need to get swapped out, it could still be done after your trip if it wasn't resolved beforehand. I guess what I'm saying is I wouldn't hold up a trip for this as long as the truck was driveable.

We are all busy, and I get that. But obviously autocraft is already reading and replying to this thread on the forum and to the time to argue with others on here - yet he wont acknowledge the actual tech posts in the thread. Also keep in mind that our PM started about 3 weeks ago, BEFORE there was any arguing or BS to wade through in this thread.

My truck is driveable, but when loaded with gear for 13 days it sags pretty bad in the rear It also needs more caster than slee caster plates can provide with the height. I don't want to do 2k miles of highway with a twitchy steering, headlights pointed at the sky (no more adjustment left) and 11 days of sagging my way though moab.

I didn't see anywhere that Darren said it was impossible to have an out of spec spring that somehow slipped through QA or was mislabled, just that it was unlikely. I can still see where he's coming from with this because of years of producing these without issue and consistently within spec.

Post #44.

We'll agree to disagree. I'm not talking about unethical business practices or outright stealing from someone. I wouldn't spend my money with a company that did those things either. We're talking about not liking the way someone communicates and not seeing eye to eye on an issue. Not the same thing in my mind. If it was, I'd have walked away from thousands of purchases, from haggling on cars, to heated discussions with the contractor that built my house. I agree, everyone is free to do as they please and if that's the stance you take for yourself, cool.

As to you last question in your last post, I will check the meaurement on my springs. I have to be honest though, you're comparing a truck with a stock front end, stock bumper etc. to a truck with a heavy steel bumper and winch, extra lights etc. Your truck is going to be taller without that extra weight. The picture you posted with your coworkers standing on the bumper, your measurements are pretty close to what mine were around the time I installed them. I've got 2 years of hard use on the springs now which is bound to make them settle slightly. And we're talking about roughly half an inch of difference between yours and mine with similar weight on the front. I'm not sure the issue is an issue? But I'm happy to help try to figure it out.

Also, the part numbers are not the same between intermediates and heavy springs. If they were how would anyone be able to tell what springs they had? The dealer couldn't be sure he was sending you the right thing if there was no difference in part number. What was the part number of your front springs? From my information the 75mm intermediates should be numbered 7501, the 75mm heavies are numbered 7511. If you have 7511, you were sent heavy springs not intermediates.

I believe you have me confused with Greenbriar, who originally created this thread. My truck has a bumper, winch, and dual batteries and is 1.5" taller than your up front.

My part numbers are posted earlier in the thread, you verified them as correct for what I ordered. Nothing in the thread is about rear springs, only front. The rear of my truck is the exact same height with the 7511's as it was with OME j springs.

I have read every thread on this forum related to slinky springs including your entire build thread. I don't complain unless I have a valid complaint, and I don't post much on this forum - it usually is not necessary, since there seems to be a thread about every problem on these trucks. I do a lot of reading on here. These springs are known for having little to no settling which is a good thing. Mine settled 1/4" on all 4 corners in the first few hundred miles, and did not change in the following 600 or so miles of heavy use. You posted about how after several years of use, yours were the same height as the day they were installed - I believe that - your truck looks great.

In all of the reading I did months ago, there were several slinky threads that had tons of relevant info with measurements and pictures which have now been deleted completely. This happened a few days after I ordered my springs (july 31), and about the time Autocraft made bunch of "NOTICE OF CLAIM" posts, which have been deleted also. I don't really care to know, but that's how I ended up in greenbriar's thread - as his was not deleted.

Again, this whole thing is over and done with. At this point, I would appreciate if we all stop posting unless there is some relevant info involved. I have no hard feelings towards anyone who posted up here trying to help, thanks again for your time.
 
I noted that my calculations were rough (based on a tape measure in my driveway) and the weigh of the front of your and lumpskie's truck was the variable being solved for in my equation - not a constant. No assumption was made.

I don't want to argue either - I like your truck and appreciate your response and willingness to help to try and help sort this out.



He spent 2 hours arguing and blaming me for his attitude. He could have spent that time working on the problem, but chose not to. I know you are some sort of brand spokesperson or something for slinky, so I don't expect you to join my side, but I would appreciate if this arguing would stop right here on an agree to disagree basis. Its over with, Kevin at EHO solved my problem.



We are all busy, and I get that. But obviously autocraft is already reading and replying to this thread on the forum and to the time to argue with others on here - yet he wont acknowledge the actual tech posts in the thread. Also keep in mind that our PM started about 3 weeks ago, BEFORE there was any arguing or BS to wade through in this thread.

My truck is driveable, but when loaded with gear for 13 days it sags pretty bad in the rear It also needs more caster than slee caster plates can provide with the height. I don't want to do 2k miles of highway with a twitchy steering, headlights pointed at the sky (no more adjustment left) and 11 days of sagging my way though moab.



Post #44.



I believe you have me confused with Greenbriar, who originally created this thread. My truck has a bumper, winch, and dual batteries and is 1.5" taller than your up front.

My part numbers are posted earlier in the thread, you verified them as correct for what I ordered. Nothing in the thread is about rear springs, only front. The rear of my truck is the exact same height with the 7511's as it was with OME j springs.

I have read every thread on this forum related to slinky springs including your entire build thread. I don't complain unless I have a valid complaint, and I don't post much on this forum - it usually is not necessary, since there seems to be a thread about every problem on these trucks. I do a lot of reading on here. These springs are known for having little to no settling which is a good thing. Mine settled 1/4" on all 4 corners in the first few hundred miles, and did not change in the following 600 or so miles of heavy use. You posted about how after several years of use, yours were the same height as the day they were installed - I believe that - your truck looks great.

In all of the reading I did months ago, there were several slinky threads that had tons of relevant info with measurements and pictures which have now been deleted completely. This happened a few days after I ordered my springs (july 31), and about the time Autocraft made bunch of "NOTICE OF CLAIM" posts, which have been deleted also. I don't really care to know, but that's how I ended up in greenbriar's thread - as his was not deleted.

Again, this whole thing is over and done with. At this point, I would appreciate if we all stop posting unless there is some relevant info involved. I have no hard feelings towards anyone who posted up here trying to help, thanks again for your time.
Glad you have it sorted out. Feel free to PM me if you have additional questions. Happy to help.
 
For the record, we asked for specific details via PM and we stand by the fact we dont do customer education on purchase via forum threads but by P.M or email. If you P.M me to ask for assistance, and then get requests for details so we can have the conversation via the medium you chose to contact us, but cant send through what is required to help you and have the conversation, then we are stuck on waiting for you to send what as requested.

We cant be short, terse, or any other unhelpful thing while waiting for you to do what is needed to help you. The idea of the request for help, and the details to know what we are working with require short precise details to concentrate on the problem.

Waffle, and rewriting history, and forum threads do not create this environment to concentrate on the data and supposed issue.

If that doesnt work for you, I have no problem with that, but setting up someone to blame for your own shortcomings on supplying as requested, and is obvious it seems to everyone else trying to help or reply in this thread, then you make your choices and move on.

You dont keep trying to blame everyone else, while you couldnt do as was requested.

Wether I read here or not has no bearing on the requests made that werent fulfilled by the person requesting details by P.M here to begin with. You need to respect that given you asked me for help.

We never received the requested details despite numerous attempts, and stated several times we would not debate the process in a forum thread.

Its obvious from the re writing of history attempted in this thread as to why we requested the details by P.M or email and why we dont discuss in forum threads.

Do the right thing, follow directions, give the data required as requested, get the right result, its pretty simple really.
 
For the record, we asked for specific details via PM and we stand by the fact we dont do customer education on purchase via forum threads but by P.M or email. If you P.M me to ask for assistance, and then get requests for details so we can have the conversation via the medium you chose to contact us, but cant send through what is required to help you and have the conversation, then we are stuck on waiting for you to send what as requested.

We cant be short, terse, or any other unhelpful thing while waiting for you to do what is needed to help you. The idea of the request for help, and the details to know what we are working with require short precise details to concentrate on the problem.

Waffle, and rewriting history, and forum threads do not create this environment to concentrate on the data and supposed issue.

If that doesnt work for you, I have no problem with that, but setting up someone to blame for your own shortcomings on supplying as requested, and is obvious it seems to everyone else trying to help or reply in this thread, then you make your choices and move on.

You dont keep trying to blame everyone else, while you couldnt do as was requested.

Wether I read here or not has no bearing on the requests made that werent fulfilled by the person requesting details by P.M here to begin with. You need to respect that given you asked me for help.

We never received the requested details despite numerous attempts, and stated several times we would not debate the process in a forum thread.

Its obvious from the re writing of history attempted in this thread as to why we requested the details by P.M or email and why we dont discuss in forum threads.

Do the right thing, follow directions, give the data required as requested, get the right result, its pretty simple really.

I commend you for being so patient! I would of said good day long ago, definitely will look at your offerings when I get the itch to change springs again....hopefully not.
 
Jiminy Crickets!
OME heavy up front, meds in the rear.
Add weight to taste.
What's the problem?
 
Jiminy Crickets!
OME heavy up front, meds in the rear.
Add weight to taste.
What's the problem?
That quote above just means you have not taken a :steer: on Slinkies... plain & simple.
 
Back
Top Bottom