SUA v/s SOA

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 15, 2006
Threads
18
Messages
214
Location
Beirut, Lebanon
Recently, and following a reply i posted bout SUA and benefits, i've been "massacred", "shut down", "bashed" by fellow mates on the site sayin that SOA is smoother than SUA and that it "runs like a cadillac" although we all know no cruiser is smooth ride material.

so i figured, even though this topic has been dried to death that all you people would contribute to this pole and post personal experience about both SUA and SOA ( good and bad ). personally i got a 4" lift and my leaf springs are under axle with a curve to create more height. although i feel a little of stiffness on the road but i'd rather go for safety rather than the dangers of SOA and the chances of my truck flipping on corners.

i would appreciate all objectivity in the replies.

one more thing, for all SUA people if you got some tricks to make it smoother it would be great. still a rookie in the department hehe.
 
Last edited:
although i feel a little of stiffness on the road but i'd rather go for safety rather than the dangers of SOA and the chances of my truck flipping on corners.

Stay Under.. SOA will always be Less "Safe" on road..
 
I have always found SOA's to be smoother rides, not sure why. But that being said there is so much special work involved for the normal person to do a SOA conversion, unless hardcore wheeling is in your future, I would leave it alone. I see no reason for a light to moderate trail rig that will be on the road to be Sprung Over.
 
I plan to re-begin my 72 ground up rebuild soon. I am also debating between remaining SUA and ordering like 6" Alcans w maybe 2" shackles or going SOA with adding single control arms for each axle. Haven't decided yet.
 
Instead of doing a SOA, and there being a limit to shackle length, why can't blocks be welded to the underside of the frame as spacers between the attachment points at each end of the springs? (One block under the spring eye, the other under the shackle attachment point.)
 
Blocks would have to be very tall to give much assistance in lift, i would think. And your fabrication would have to be pretty good to align everything correctly.

Fabrication isn't really a problem. It's just a cheap solution that does not help off road. By just lowering the suspension you do not have any more clearence. Having just done a soa on my cruiser I would say that if you want smaller than 35's run a 2.5" lift sua. Any bigger and soa is good.
 
:shotts:

SOA is for wheelin' with tires 35 and up but drives just fine on the hwy...

SUA is for DDs, Grocery getters and Mall Crawlers....

IMHO :cool:

As for SOA being smoother, it just is... (the old stock springs are much softer than lift springs).
 
Bumper Height Laws

Something that may NOT apply to some of the folks, whose only response is " SOA ! " when a suspension lift question comes up, is various bumper height/ lift laws. In some states ( Mo, for instance ) we have to get a vehicle inspection every 1-2 yrs, so got'a keep it simi legal. SOA is cool, but for myself, I want to see what can be done with a SUA, as thats what I have to deal with. Al
 
LukeO,
what are single control arms?
is this similar to sway bars?

I too have a 55 SOA, that rides like a dream...but if you jerk the wheel you feel like you're going over. It has no sway bars. and would like to stabilize it without losing the cushy ride.
 
Yup, law says 24" from lowpoint of frame that is. My '74 FJ40 DD is SOA on 35s and measures 23" to the frame. The old "worn out" stock springs are soft and supple. Gives a nice ride and flex...

my buddys and i just throw on some 29" mall cruise'in tires to get an inspection, as for after the fact most cops dont cary around tape messures or properly know the lift laws ( since in mass the lift law is two pages long f&^%ers)
 
well,


ah forget it

my hand just got tired thinking of all the things i was to type.
 
Instead of doing a SOA, and there being a limit to shackle length, why can't blocks be welded to the underside of the frame as spacers between the attachment points at each end of the springs? (One block under the spring eye, the other under the shackle attachment point.)

Brian

This is something I have been wondering about lately. After a lot of thought I have come to the conclusion that for a short lift (max 2") it might be okay for a rig that will not see extreme wheeling, but I am not experienced at working on suspensions. I have read a lot of complaints here on Mud about lifts being too stiff. I have also read about SOA with stock springs being better riding. By using short blocks and stock springs, or maybe even 55 or 60 series rear springs front and back, you would have your stock feeling ride with a little better articulation and additionally have some room for larger tires.

My thoughts are that anything like a 4" lift block would probably create lateral frame stress problems in a rig that was wheeled heavily.

I would like to get some feedback on this, pro and con, but I don't want to take away from Cruiserfreek's thread. Maybe a new thread could be started on this topic.
 
Stay Under.. SOA will always be Less "Safe" on road..

Why? If you put a 4" lift with 2" shackles, you're lifting your truck 6 inches. If you SO, you're still sitting at around 6". The weight of the truck would still be the same around corners so why would one lift be 'safer' than the other? I would actually think it would be the opposite. If you put all the suspension travel in a spring/shackle lift I would think you'd be a little less stable in corners.
Sorry to continue the horse beating...
 
Stay Under.. SOA will always be Less "Safe" on road..

What he said. An SOA will never be as safe as a SUA when it comes to pavement.
 
Why? If you put a 4" lift with 2" shackles, you're lifting your truck 6 inches. If you SO, you're still sitting at around 6". The weight of the truck would still be the same around corners so why would one lift be 'safer' than the other? I would actually think it would be the opposite. If you put all the suspension travel in a spring/shackle lift I would think you'd be a little less stable in corners.
Sorry to continue the horse beating...


If a SOA is more flexy, then I think that would cause alot more body roll on turns.
 
Back
Top Bottom