power steering conversions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 12, 2006
Threads
2
Messages
5
I'm working on a 1965 FJ40. I took out the F engine and replaced it with a 2F.( just to see what a stright 6 is like. I never had one.)
I'm wonder what other types of power steering conversions are out there? I know about the Signaw or a Bolt on kit, which is like the stock power steering out a 70's FJ40. But I'm hearing about using a minitrucks power steering or something like that. I'm running low on money, so that is part of my searching for other ways to have power steering. any suggestions.. thanks
 
I have both brackets to do the Mini truck gearbox and
the Saginaw P/S pump.That includes all the mounting
hardware,spacers and adjusting arm.
They are $95.00 each plus shipping. If you buy both
they are $180.00 plus shipping.
Send me your address and what you want and I will
email you a total.
You can see pictures at the below web site and a good
post on ih8mud. Thanks
Bill

http://photos.yahoo.com/wdorry
https://forum.ih8mud.com/showthread.php?t=65318
 
Scout Box

I like my Scout p/s setup ( simular to a FJ 60 box, i believe ). When I was looking at my options, and the amount of work involved to install, it seemed like a no brainer. Some triming of the fenderwell, plate the outside of the frame aprox 3/4" ( to get clearance between p/s box and radiator mt ), and drill 3 holes. Box mounted. Make sure to use some fairly heavy tube spacers inside the frame for the bolts, so that when the bolts are tightened, it dosent collapse the frame. After grinding on my shock mount to get it to clear the p/s box ( waste of time ), I went with the Ford shock tower, and cut it to match the length of the stock one. If you go this route ( on a 40 ), you'll wind up aprox 37" for relay rod length ( if you have to make your own ). Al
 
GO WITH BILL DORRY'S DEAL ,, ALL BOLT ON, VERY LITTLE FAB WORK. IN FACT ONLY WORK WAS GRINDING THE OLD BRACKET BOLTS OFF, SEE THE LINK AT THE BOTTOM OF HIS THREAD. (ROMER'S WRITE UP)
JUST DID MINE, MINI TRUCK POWER STEERING..
WORKS GREAT ... ;)


https://forum.ih8mud.com/showthread.php?t=65318

HERE YA GO .. READ ON ,,,,,,

GOOD LUCK ,,

AND AS ALWAYS :beer:
 
i like the write up i have a somewhat similar setup. glad to be apart of the few..:bounce2:
 
My saginaw works great, but after seeing what Mark W does with the FJ60 box it is a great route to go. No hacking into the crossmember.
 
My scout set up is working great, the box only cost me 50$ at a local junk yard.
 
while im still running arm strong steering i have looked into power steering set ups and asked around....from what i have heard the mini truck setup is a little weak if your planning on going with some big rubber...but prolly good till around 35", again i dont know this from experience just the grapevine....im sure other will chime in. im going saginaw on mine....might look into the 60 though...
 
i have a scout box for sale if you're interested.

i'm not a big fan of the jt outfitters conversion or any other for that matter using the mini stuff or re-using the factory bell crank and relay rod. the TRE at the ps box ALWAYS ends up getting bent and if you run tires larger than 31s they will hit the relay rod.

go with one of the sag or fj60 box setups.

i have a few of the sag mounting plates for sale as well.
 
Thanks for all of you help!
I was considering a bolt on kit from classic cruisers. the kit could be found at:
http://www.classiccruisers.com/pages/conversions.html
I hate to sound like an idiot, but is this anything close to the fj60 power steering? or is that more of a stock power stering set up? I never seen the power steering set-up for any other year.
I dont have to tools to do any major conversions. I know that a Signaw would be the best route, but I'm looking at my experience with mechanics and tools available to me. bolt on would be the easiest way to go. if anyone has parts in the Nor CAl area I'd like to try to buy them and pick them up. Just to cut-out shipping cost! you can e-mail me at fh_36@yahoo.com
 
Thanks for all of you help!
I was considering a bolt on kit from classic cruisers. the kit could be found at:
http://www.classiccruisers.com/pages/conversions.html
I hate to sound like an idiot, but is this anything close to the fj60 power steering? or is that more of a stock power stering set up? I never seen the power steering set-up for any other year.
I dont have to tools to do any major conversions. I know that a Signaw would be the best route, but I'm looking at my experience with mechanics and tools available to me. bolt on would be the easiest way to go. if anyone has parts in the Nor CAl area I'd like to try to buy them and pick them up. Just to cut-out shipping cost! you can e-mail me at fh_36@yahoo.com

I've got the Classic Cruiser hardware and their brackets and pulley setup are first class. I run 33x10.50 and have no problems with the setup.
 
I think that it would be best for you to meet up with some other Land Cruiser people that have power steering in their truck, look at how it was done, and then see if they will let you operate their truck so you can get to feel some of the different systems. There are A LOT of 40 series folks around Nor Cal...



That way, you do not spend a bunch of money on something that you do not really end up wanting.


Good luck!


-Steve
 
Back
Top Bottom