Is it a good one?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 19, 2006
Threads
1
Messages
14
Location
STL MO
While im hardly new to the 88-95 trucks/4runners this would be the first FJ40...

Ive wanted one for a while now, and had my eye out for that "right" one...

I THINK ive found it...

72 FJ40...stock drive train, runs (needs some carb work) shifts fine, etc Current owner says he has a hard top and doors to go with, although slightly rusty, and has a title...

So if im going to arange to go out and take a loook at it this weekend (bout an hr outside of town) ... what should i be looking for, and how much should i be spending?

fj40_1.jpg


fj40_2.jpg


fj40_3.jpg
 
Lotta rust and repaint in wrong color, if it runs okay I'd say 2500
 
It's rusty and it's got carb problems (if not more, for all you know). As you're aware, you can replace the nasty rust bucket tub. As for the carb (if it's just that), read some of the current threads in this and the 60/62 forum to prepare you for your impending heartbreak and stress.

If the thing has good compression, a good frame, and a good drivetrain, I'd consider buying it. But for a truck like that I'd go LOW-ball on any offer I made.
 
Not sure what you guys are seeing, but that tub doesn't look THAT rusty. Further, rough running "carb" problems could be a simple -plugs, wires, rotor and points-job away...just as easily as it could be a more expensive problem.

I agree on checking the frame before purchase. Hell, you could even check the compression and do the simple tune up mentioned above and a carb adjustment before purchase to see if it runs any better.

Good luck! I purchased a rusty junker for $950 a few months ago. I now have it running great...but have dumped another $500 or so into it since then. It will cost you money, no doubt. Best to try a low ball offer first....then offer to meet halfway between your low ball and his reply to that offer.
 
Welcome.




Lift up all the floor mats and see just how much of the floor under the driver and passenger feet and the rear of the tub no longer exists.

Verify weather or not that the carpet or expanding foam insulation covering the inner rear fenders inside the cab IS their only structural integrity.


I personally would have a very difficult time spending anything over a grand on a truck of this vintage and condition considering the corrosion that is very evident in this vehicle.
In the end, it really only comes down to you being satisfied with your purchase, as you are the one that will end up dealing with any of the issues this truck has or develops.



Good luck!


-Steve
 
I am with poser, all that matters is you being happy with it, but I would be looking to spend up to probably $1000 on that truck, maybe another hundred or two if I had been searching for a while and couldn't find them in my area. Best way to figure out the rust issue is to go through the $pector and Man-a-fre catalogs and look at what patches are available. You'll have a good idea where the trouble spots are and what it costs to fix them. And of course inspect the frame throughly.
 
Definately check the floors, but the rest is not THAT bad, cut it off. And yes you cannot drive it with jeep lights. As stated above only you know what it is worth to you. And remember this does not drive like a mini truck, more like a farm implement.
 
I would also check the emissions if you need to have it emissioned where you live. The back part of the front seat that is missing had a emission tank in it. Plus I think there should be a tank was in the rear of the passenger's rear wheel well opening. I would also check for bondo. The driver's side rear is missing the emblems and the holes are filled, plus the hole for the backup light looks to be filled in. Looks like it was already repaired once and rusting thru again.


John
 
I think I'd start at $500 and maybe pay up to $1K at the very most. You can get one in a lot better shape for your money.:cheers:
 
everyting about that rig bums me out: color, 2nd color, green interior, interior itself, but mostly the major rust... I know you need to start somewhere (I looked for years), but this one just feels like trouble (just looking at the rust itsef) from the photos. could be way more than you want to get into? check it out... but 1K would be the most (and I would be hard pressed for that I see here).

BUT, if that soft top is in nice shape, you could sell it and recoup some $$.

BTW - is that a 3 on the tree?
 
Living in the Past said:
I would also check the emissions if you need to have it emissioned where you live. The back part of the front seat that is missing had a emission tank in it.

Correct: evaporative emissions device. It seems there is some booty fabbed plumbing to the front on it now :confused:

Living in the Past said:
Plus I think there should be a tank was in the rear of the passenger's rear wheel well opening.

what would that tank be for? I sure don't have anything different at the passenger rear wheel well than the driver's side in my truck. I would be delighted if you could enlighten me. Thanks.
 
My body was in much better shape, the frame was perfect, the motor didn't run though probably could have ... I paid $800.

I would run away. Too rusty for me, unless you plan on replacing the tub.
 
It's gonna be a project for sure but it looks to have alot of things that are normally missing.The rust is an issue but there aren't alot of guys running around with Rust Free rides.It really depends on your intended use/skills and of course cash flow.You'll still need to check that frame out and I'd take some goggles and tools.Its still better than the heep those lights came off of!!!Good luck and welcome to MUD.
 
75+ had more creature comforts and brought the vehicle into at least the 1960's as far as technology is concerned. 75/10 and on got front disk brakes. 78 is thought by some to be the most desireable due to disk brakes and stronger pinions. But then again 79 and on saw stronger steering knuckles and got away from the bastid birfs, added the posibility of factory air and powersteering, etc.

In the end if it's what you want and you feel you bought it right than go for and welcome to the dark side. I'm not really a me too, but the statement about it being a farm implement hits the nail on the head. Good one's are getting hard to find.
 
Quote: DSRTRDR

what would that tank be for? I sure don't have anything different at the passenger rear wheel well than the driver's side in my truck. I would be delighted if you could enlighten me. Thanks.


I'm not sure if the 72s had it but the 71 I parted out did and the 71s and 72s shared the same parts in the seats. It was a tank that was mounted in the rear of the wheel well on the passinger's side. If you had it there would be holes on the top of the wheel well that don't match holes on the other side. I don't remember but I think the tank was mounted to the top of the wheel well. The part I remember is the skid plate that was used to protect it. I've collected four over the years out of junk yard. They mount with two bolts to the top of the wheel well and two on the bottom toward the back. This skid plate kept mud from getting kicked up on the tank. My thought was if you install them all the way to the back it would help keep the mud from collecting in the back corners. If you want I can post post a picture of the skid plate.

John
 
Back
Top Bottom