Easiest v8 swap

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 26, 2015
Threads
63
Messages
255
Location
las vegas
so Im replacing this motor in one of my trucks because it has 258 miles and my head gasket has been replaced multiple times, I’ve been planing on doing a rebuild but then cost wise i figured i should just put a reman engine in it. Does anyone know if it was be about the same price for a v8 swap to a 1fz replacedment.

Also i wanted to know opinions on the easiest best engine to install and if i would have to make a lot of custom mounts and maybe see if i can still use the same trans with a v8 swap ....
 
so Im replacing this motor in one of my trucks because it has 258 miles and my head gasket has been replaced multiple times, I’ve been planing on doing a rebuild but then cost wise i figured i should just put a reman engine in it. Does anyone know if it was be about the same price for a v8 swap to a 1fz replacedment.

Also i wanted to know opinions on the easiest best engine to install and if i would have to make a lot of custom mounts and maybe see if i can still use the same trans with a v8 swap ....

How many head gaskets have you gone through?
 
a 2uz-fe swap out of a 100 series would be effective. More power and torque plus it uses the same Transmission as far as i know.
 
a 2uz-fe swap out of a 100 series would be effective. More power and torque plus it uses the same Transmission as far as i know.

Yes but no. Lots of changes. You cannot simply bolt the 1fz 343 to the 2uz. Would need a complete setup. You also cant just grab a tundra or sequoia engine either. Needs to come from a cruiser for the accessories and oil pan to work. Then there is the wiring... ls is the only way to go imo.
 
Yes but no. Lots of changes. You cannot simply bolt the 1fz 343 to the 2uz. Would need a complete setup. You also cant just grab a tundra or sequoia engine either. Needs to come from a cruiser for the accessories and oil pan to work. Then there is the wiring... ls is the only way to go imo.

Agreed. LS makes the most sense if you want a V8. Most power, least work.
 
Easiest and cheapest is obviously the 1fz. You might figure out why it needed more than one HG replacement.
 
I think the easiest would be to buy a 100 series.
 
I think the easiest would be to buy a 100 series.

I kind of went this route but bought a 2003 4Runner with the 4.7. The power to weight ratio is nice and the cab space is immense compared to my 80. I found the 100s to be a tad on the bulky side so I went for the 4runner. I love them both and will keep them both for a long time.
 
6BT.......
4BT.......
 
There is no correct answer to this question, every one has an opinion.

My opinion is:
  • Simple and relatively cost effective option: - Rebuild your 1FZ-FE and turbo it with wits' end Turbo kit.
  • V8 Option: LS variant since parts can be had relatively cheap and a lot of documentation around the conversion process. Still a lot of work and if you aren't doing it your self, gets very expensive ($20-$25k)...mostly labor.
  • Diesel Option: 6BT Cummins - Not cheap even if you do all the work yourself, but parts availability, conversion documentation and raw power are why its the way I would go.

Full Disclaimer - I have a Cummins 80 and a To-Be Turbo's LX...I don't have an LS Powered 80.
 
Easiest V8 swap is to buy one that is already complete and dialed in, has thousands of miles on the swap to prove it works.

Exactly !
 
Easiest V8 swap is to buy one that is already complete and dialed in, has thousands of miles on the swap to prove it works.

This doesn't appear to be the case in the 80 swap world from what I've seen. Seems like the converted units go on the chopping block more often than not. Of course, there are exceptions but this seems to be the norm
 
  • Like
Reactions: ppc
This doesn't appear to be the case in the 80 swap world from what I've seen. Seems like the converted units go on the chopping block more often than not. Of course, there are exceptions but this seems to be the norm
You'd have to pry my cold dead hands off the steering wheel of mine.... While fighting off several other people trying to do the same;)
 
Back
Top Bottom