ARB vs Lockright...

If you were me, you would run...


  • Total voters
    52

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Yeah I'm with Zach on this one. For $1k you can get two lunchboxes and have plenty left over. Enough for Longfields or a cage or....

IIRC there are threads on running an ARB off of CO2.
 
bustanutley said:
ARB involves a whole new carrier, which means you have to have your gears setup. You can do it yourself but it isn't an easy task, I have read articles but have yet to do it myself. Normally a farmed out gear install is $100 for labor and the setup kit is $100 from kurt. I'm pretty sure a compressor is pretty much manditory. If it were me, I would do what I did again, get 2 lunchbox's for 2/3 the price of one ARB. Pretty much you can go anywhere locked front and rear. I have DD mine for 4 years locked front and rear.

'Nutley-

Maybe I could catch a ride in your ride and get a first hand feel for the characteristics of the lunch box lockers. Let me know when you are swinging by lousiville again. Or acutally, I am in Boulder like everyday.

Rezarf <><
 
REZARF said:
'Nutley-

Maybe I could catch a ride in your ride and get a first hand feel for the characteristics of the lunch box lockers. Let me know when you are swinging by lousiville again. Or acutally, I am in Boulder like everyday.

Rezarf <><

Yeah totally dude, that is a good way to see how they are, it just takes getting used to, I think it is fun on the road!
 
Rezarf;

I Aussie'd mine recently, you can drive it at the next RS meeting if we both end up there. Or if you can drive Nutley's before then.

It does not offer infinite differentiation in the road. FJ Ben and I were Cruising down the canyon last weekend and I had to be a little more mindful in the turns that I know well... Ben on the other hand was stuffing that Pig in there.

You might as well pay for an entire rebuild on a third member when you drop an ARB in - get new bearings, set your preload correctly. Robbie at Slee can do this for you (see him at RS meeting), but you are probably talking an additional $400...

Good luck! Let me know if you want me to bring the 40!
 
PabloCruise said:
Rezarf;

It does not offer infinite differentiation in the road. FJ Ben and I were Cruising down the canyon last weekend and I had to be a little more mindful in the turns that I know well... Ben on the other hand was stuffing that Pig in there.


Yeah I imagine it was a little scary for everyone to see this gigantic pig flying through the corners with sports car enthusiasm. I grew up driving that canyon but I'd imagine I'd drive a bit differently with an Aussie or Detroit....

And in other news...

How soon are you looking to get this locker? Maybe you could wait for a winter/icey day THEN try someones Aussie locked rig out...I'm sure it will snow on halloween...always does...then you don't have to guess how it will do on the snow vs. dry roads...just some more of my thoughts...
 
If you are going to go ARB, please have someone that knows what they are doing set it up.


Slee was going to be my first suggestion. Dealing with a quality shop that will be there to help you with warranty issues, or anything else that may arise, in the end, is priceless.


Burnt up ARB compressors.....got 8 years out of the first one, and only took it out to 'update' the system to the new compressor, when I 'updated' the axles in '99....

It is not designed as a continuous duty compressor. It will give you years of reliable service when used inside its intended operating parameters.

only know of one ARB compressor/wiring issue in the 14 years that I have been distributing their products, and it was from a relay that stuck on, and would not release....

:beer:


Having spares of anything 'kustom' on your vehicle only makes sense.
 
Last edited:
FJBen said:
Yeah I imagine it was a little scary for everyone to see this gigantic pig flying through the corners with sports car enthusiasm. I grew up driving that canyon but I'd imagine I'd drive a bit differently with an Aussie or Detroit....


I thought you may have been working that Pig like it was a summer job!
 
arb....

Hands down. I use mine in front for driveability issues
on AND off road. Front lockers can make turning a little
limited when they are engaged. Psssssst.....unlocked
and turning easy. Flip a switch and relock.
I love my Lock Right rear too. I like it's mechanical
"feel it" working traits. Very old school cool.
It makes the nicest little chirps on demand leaving
any stop.
A rear ARB is in my future for side hill and snow/ice issues.
I just hate losing the old clunking, reassurring reminder
that the monster is locked. :)

Dealer install helps when it comes to warranty.
I had the ARB installed into my 3rd member and
took it from there. $200.
I like using an air tank. It'll on and off all day without
tripping the compressor. I hate hearing the compressor
switching on and off all the time.
 
bustanutley said:
ARB involves a whole new carrier, which means you have to have your gears setup. You can do it yourself but it isn't an easy task, I have read articles but have yet to do it myself. Normally a farmed out gear install is $100 for labor and the setup kit is $100 from kurt. I'm pretty sure a compressor is pretty much manditory. If it were me, I would do what I did again, get 2 lunchbox's for 2/3 the price of one ARB. Pretty much you can go anywhere locked front and rear. I have DD mine for 4 years locked front and rear.

If you're keeping the same gears you just have to set the carrier side to side. That's not difficult if you have a solid mounting for a dial indicator, and ARB's instructions are step by step easy.

Getting a clean run with the copper internal air line, making a straight - in connection to the junk that goes through the housing that (hopefully) won't leak was the only thing about an ARB install that gave me trouble and mostly that was because of my own hesitancy to cut the line too short and avoid having to resquish the connectors. It'd been better if I'd have just laid in some spares for just in case I blew it.
 
For me though, my 3rd member needs an overhaul, my pinion bearing is pretty worn out and i figured I would go through the whole thing while it is out. Prolly slap disks onto the rear while I have it out too.

Rezarf <><

Still leaning towards the ARB, getting some quotes now.
 
I thought twice about buying two lunchbox lockers instead of one ARB, but realized that I would always want an ARB. I decided that I would rather fork the cash and have the best.

I doubt I will run anything else in one of my trucks, ever. I even wish I had ARB's in my 80 vs the stock lockers it has.
 
Kurt-

Did you get the complete 3rd members priced out? Could you PM me with a quote.

Thanks!

Rezarf <><
 
Back
Top Bottom