'94 Center diff/lockers issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 4, 2018
Threads
2
Messages
10
Location
Lagrange, IN
I recently purchased a '94 LC triple locked with 164k on it. One gentleman had owned it and passed it down to his daughter. Over all in very good shape.

My question is: when I place it into low the center diff light does not come on. I try to engage front and rear lockers, the lights just blink.

An ih8mud member made mention that he had the same thing and the forum had guided him to a fix. The position sensor. I am looking for information or additional theories on it. lol!

I appreciate any experience or insight!
Joe
 
On the '94 model the front and rear lockers will not engage until the center diff is locked. Try listening for the actuator trying to engage as you put it in low (remember the transmission needs to be in N). You can also try driving a little at low speeds to see if it engages. If none of that works the it's time for some troubleshooting. Hopefully it will free itself first.
 
I have tried several times to get her going. The low speed in low works as I expect it should, but I don’t hear an audible click (a buddy has a 95 and 97, says there is a click) and no light.

The above mentioned member mentioned a position sensor.

I had a few people suggest a “7pin mod” which I began reading on a few days agozzzz
 
Just to be sure I’m engaging it correctly, it goes as follows. Please correct me if I’m an idiot and screwing this up:
Place in N
Shift down to L
Wait a moment
-light should light and click should click
Turn locker knob to rear
Turn locker knob to front
All three lights should be solid

Just wanna be sure. And when placed in 4Lo the center diff should light and the click should click, correct?
 
do you have a center diff switch in your dash ? we do on our '93
 
On my truck i had the same problem, what i found was the ball detent switch on the transfer case was gummed up. From my research this seems to be a common problem on these trucks that were never used off road, that means they were never shifted into low range thereby working that switch. Most of the time if you remove the switch from the transfer case and clean it with contact cleaner, while pressing the ball in and out a few hundred times. That should clean it's internal contacts and get it working again.
 
Like @DSRTRDR said, look for a switch on the dash that might lock the center diff. Some people add this because the wiring is already there and it lets them choose Center Locked in either HI or LO. Research "Pin-7 CDL Switch" here in the 80's section. You'll get a lot to read but it's all simple stuff. If you have the switch, when pressed, it'll engage and activate the CDL light whether you're in HI or LO, and it eliminates the stock method of automatically locking in LO. Make sure the key is in the RUN position but the engine is off (so you can hear the clicks). BTW, the switch will be OEM and might be unlabeled, or it might say 4x4 or CDL or have an image of some kind that you don't understand yet.

Read this: CDL Sensor/Switch ......

...to understand what this picture means. Once removed, you can spray the ball end of the sensor with contact cleaner while cycling it a few hundred times. Then hook up something like this and keep cycling it. A multimeter can help speed up the process by checking for resistance, but it's not necessary.

IMG_1205.webp
 
This may be obvious, but didn’t see you say it.
Just to be sure that after you have engaged the lockers that you drive the truck on gravel or grass so that the drive shafts and pinions are turning allowing them to lock. Just try the rear only at first driving slowly left to right. I have to spin the wheels some or travel about 5 feet to fully lock.
They hopefully just need to be exercised. My lights just blinked also until 10 times trying back and forth side to side. Work like new now.
Here’s a little info, keep on searching...
Lockers Won't Engage

Just to be sure I’m engaging it correctly, it goes as follows. Please correct me if I’m an idiot and screwing this up:
Place in N
Shift down to L
Wait a moment
-light should light and click should click
Turn locker knob to rear
Turn locker knob to front
All three lights should be solid

Just wanna be sure. And when placed in 4Lo the center diff should light and the click should click, correct?
 
There are two sensors on the transfer case. The one on the driver's side (or rear, center, I forget) is the low-range sensor. The one on the passenger side is the CDL sensor.

CDL Sensor Location
 
There are actually three sensors on the transfer case. The CDL indicator sensor is on the front side. Its function is confirm the CDL is actually locked and to disable ABS. There are two sensors on the rear extension housing. Looking forward from the rear, the sensor at the 1 o'clock location is the 4LOW position sensor which senses that the transfer case has been shifted in low range and activates the CDL actuator. The sensor located at the 10 o'clock location is the transfer case neutral position that illuminates the AT/P dash light when the transmission is in Park and transfer in neutral to warn that the truck can freely roll.
 
Don't see how installing a dash switch or pin7 is going to help, the system has to be working. The first question is what works and doesn't, so basic understanding of how it works is helpful. The documents posted on this page explain it well. Sometimes it's helpful to jack the rig up for testing, then wheels, drive shafts can be turned, better observe what is working without driving. CDL Actuator Fun
 
some of the '93/'94 came with a center diff lock dash switch from the factory - consequently, the center diff will not lock without that switch pushed
 
Last edited:
Back
Top Bottom