Lockers Won't Engage

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 20, 2013
Threads
24
Messages
45
Location
Carlisle, PA
Over the weekend I bought my first LC, a white 1994, with factory lockers. The seller said when he bought it the lockers did not engage but he "cleaned them up" and then they worked. He said he did not engage them ever again and now when I flip the switch the lights just blink and do not ever go on solid. I have tried to engage them several times while in low range and in neutral and they will not go in. Are there and easy places to start to try to free them up? Should I remove the metal covers from the tops of the axles and clean up the connections? I believe it is fairly common to have some issues if they were not used very often. I would obviously like to make them functional as they were a major reason for purchasing this vehicle. I have begun to make a list of things to do to my LC and have just started filtering through the info on this great site. Thaks in advance for any help on troubleshooting these lockers.
 
Try doing slow figure 8's on loose gravel in 4low while trying to get them to engage, see if you can get them to lock up that way first. They might just need some excercise.
 
when searching arount the forums "e-lockers" is a term we use for the factory locks - and I posted a while ago the color code wires to just jump under there & use a 9v battery & a few scrap short wires to "jumpstart" the motors (and unlock too) - but like Kevin posted above me, the CDL IIRC is a permissive for the locker motors to cycle - but at least with a 9v & a few scrap wires you can see if the locker motors are good & the problem is further back in the system.
 
I hate to bed get the obvious, but have you locked the center diff first, or at least put it in low?
 
Also you do realize that the vehicle must be moving with wheels turned. Although they could theoretical look with the wheels straight they would do so almost immediately. By driving in a circle you are creating increased RPM differential between the axle and locker dog collar thus increasing the opportunity for the locker to engage.
 
Last edited:
Maybe I do not completely understand the CDL. I do not have a CDL switch on mine (yet) but I have put it in low range. Is there another way for me to engage the center diff? I will be getting a CDL switch installed soon. It is on my to do list. I will try putting it in 4 low and engaging the locker switch and doing some figure 8's to see if I can get them to engage. I have read a few posts on here where several members have said their lockers engage in a second or two after turning the switch. That is ultimately how I would like mine to operate as well.
 
If you don't have a CDL switch, then you need to put it in 4low to engage the CDL. The CDL must be engaged before the F&R diff locks will engage, that's just how things are wired.

With that said, when you put the truck in 4low, does the CDL light go solid, indicating it's locked? If yes, then engage the F&R diffs and do some slow, figure 8's in loose gravel and see if you can get them to lock up as well. If yes, then they just need excercise, and they'll get quicker with regular use. If no, then you have some more digging to do.
 
If you don't have a CDL switch, then you need to put it in 4low to engage the CDL. The CDL must be engaged before the F&R diff locks will engage, that's just how things are wired.

With that said, when you put the truck in 4low, does the CDL light go solid, indicating it's locked? If yes, then engage the F&R diffs and do some slow, figure 8's in loose gravel and see if you can get them to lock up as well. If yes, then they just need excercise, and they'll get quicker with regular use. If no, then you have some more digging to do.

Ian: did you get rid of your HDJ81?
 
If you don't have a CDL switch, then you need to put it in 4low to engage the CDL. The CDL must be engaged before the F&R diff locks will engage, that's just how things are wired.

With that said, when you put the truck in 4low, does the CDL light go solid, indicating it's locked? ...

Yep, the CDL light must be on for the axle lockers to work.

Getting the axle lockers to lock/unlock when not needed can be a trick. So to test them, my preferred method is: Lock the CDL, jack up the rig, turn the switch to lock the rear, should hear the actuator motor run, the light is flashing, turn one of the rear tires, it should lock, repeat on the front. Now the splines/gears are lined up and can lock/unlock as many times as needed. If they work in this mode, will work when needed on the trail.
 
The way Tools R Us wrote up should be a sticky in itself, this sounds like the most sure why to check them. The figure 8 method would work as well, but this way, you can actually watch as it's happening.
 
Ian: did you get rid of your HDJ81?

Your PM's are full. We suffered a garage fire at the end of Jan, lost my truck, the parts Cruiser, wife's car, my snowmobile, and everything that was inside. Nobody was hurt thankfully, but it's been a tough month.:frown:
 
Your PM's are full. We suffered a garage fire at the end of Jan, lost my truck, the parts Cruiser, wife's car, my snowmobile, and everything that was inside. Nobody was hurt thankfully, but it's been a tough month.:frown:

OMG. I am really sorry to hear that! :frown:
 
When I put my LC in low range I do not get any indicator lights on the dash at all. No low range light and no CDL light lights up. This is a new vehicle to me so I was not even sure if there were supposed to be lights that lit up but I assumed that there would at least be a low range light.
 
When I put my LC in low range I do not get any indicator lights on the dash at all. No low range light and no CDL light lights up. This is a new vehicle to me so I was not even sure if there were supposed to be lights that lit up but I assumed that there would at least be a low range light.

There is no low range light, just the yellow center diff lock light a couple spots to the left of the CEL. If the lever is forward, you're in high, if it's back you're in low, if the AT/P light is on you're not engaged in either. If you get no light at all, you might have a problem.

I had a similar experience with the rear locker when I first got mine, getting out in the dirt where you can drive in circles or weave around will show you if they're working or not. Mine were fine.

Also, the claims you've read of instant engagement are likely from those with air lockers. The indicator lights on those systems only show that you activated the actuator, not if it is actually locked.
 
If your putting it i 4Low and the Center diff lock light is not coming on it could be the Center diff lock indicator. Slee has a good writeup on it http://www.sleeoffroad.com/technical/tz_centerdiff.htm

This is what was wrong with mine when I bought it. The seller said they didn't work. The center diff was actually lockings but the indicator was not confirming that it was. Replaced the indicator on the transfer case and now it works
 
If your putting it i 4Low and the Center diff lock light is not coming on it could be the Center diff lock indicator. Slee has a good writeup on it http://www.sleeoffroad.com/technical/tz_centerdiff.htm

This is what was wrong with mine when I bought it. The seller said they didn't work. The center diff was actually lockings but the indicator was not confirming that it was. Replaced the indicator on the transfer case and now it works

This was the issue with mine as well. Since no one mentioned it, in addition to the yellow cdl indicator light you should also get a red ABS light when the cdl is engaged. Even with the 7 pin mod and cdl dash switch mine does not always come on. I have driven for 4-6 hrs of trail wheeling without the cdl engaging. It can be very frustrating to not have 4wd or lockers when you really need them.
 
Back
Top Bottom