Gday everyone, been looking into removing my ACSD but couldn’t find a lot of information on how to do it, so I jumped right in and gave it a crack, and thought I’d put a post up on how to do it. The blanking plate I used was off of a TD42 10mm injection pump, pretty certain most VE pump blanking...
It seems like there are plenty of posts to diagnose most issues with the EGR system, but I think I’ve ran into a problem that’s not covered much.
I’m testing my EGR modulator. Looks brand new, clean filter inside, diaphragm holds vacuum when applying vacuum to the exhaust (bottom) nipple...
Alright winter is approaching and I really need to get coolant in my engine. I need advice on a few things on how yall would about dealing with them. My cooling system is original down to the original pump that still surprisingly still works and doesn't leak at all. The barring is shot and has...
Factory AC System from 1979 FJ40 Landcruiser. Installed by CCOT during a previous restoration. I purchased the FJ40 and removed the AC to install Vintage Aire during recent restoration. It was not charged and I never tested it when I purchased. Includes inside blower unit, compressor...
I'm in the process of picking up another 200 and plan to add a drawer system - ARB or Dobinsons. Only reservation is that I have a dog kennel - Gunner Intermediate - that I need to fit on top. Does anyone have measurements of the space between the top of the drawer and the roof of a 200? Thank you!
Ok guys help the idiot. I know the primer for the fuel system on the LJ is on top of the filter housing. I put a new head on this truck so the system is completely dry.
Have cracked the injectors so they can bleed and pumped the primer on top of the filter.
The primer button only moves...
Hi, I purchased a new stock exhaust system for a 1977 Fj40 and was hoping for a picture of the hook shaped bracket that hooks into the two rubber donuts on the middle bracket. I've looked all over the site but not able to specifically see that part. Thanks.
I want to replace my BJ40s (B engine) exhaust from manifold to tail pipe. Of course, no catalytic converter needed. I've called a few shops in town and they all seem to hover around $1200-$1500.
Seems a little pricey, don't you think?
I'm making a wheeler rig out of an 80 series that had an impact that ruptured the AC condenser in the accident, all freon and whatever else was in the system is gone, lines are off and free to atmosphere currently.
In rebuilding this beast for service again, I have no plans to try to rehab the...
So for the last 10 years or so, my 1985 FJ60 has been in a sort of hibernation, mostly staying in the garage and only making it out for runs to the transfer station (aka garbage dump) and an occasional trip around town to recharge the battery. In the near future, I'm looking at taking some road...
I was getting knock sensor code for new knock sensors, I swapped the sensors to see if it was the harness or the actual sensor.
Now getting system too lean on both banks
Any pointers?
Hey this question is for those that have put an LS engine in their rigs or general mechanics. The PO installed a LS engine but did not install the AC. So I know I need a Chevy compressor to fit the engine but from there is where I have my questions regarding equipment replacement. The PO left...
2000 LC 100
First Heater isn't blowing hot air, now AC MOTOR above front passenger feet is clicking like a kid riding a bike with a baseball card in its spokes.
I already flushed the heater core with no improvement.
Is that AC MOTOR above front passenger feet easy to replace?
Are these...
Hi all, I want to start doing some basic diagnostics on my LC 100 by myself. I have found that there is hardly anyone to help me here whenever I need some basic diagnostics.
I was thinking of a very basic one for starters, where I can use my laptop (Linux or Windows, but preferably Linux)...
My antique DeWalt 18v NiMh needs to go. The sea of different systems in the tool store did my head in!
I realize everyone has their fave - but - there must be things people wish their system had, or things they have that other systems don't have... hence my question!
My goals:
#1 - safe to...
I will be completing a 79 BJ40 & am looking for styles of pulley removal systems for topless operations. Constructed with removals in mind. Safety tip or suggestions are as always, greatly appreciated.