stock

I'm looking for the stock bracket that holds the lower fuel filter (between the tank and the fuel pump) to the chassis. My unit is a 1974 FJ40. Dave Dillon buscando13@sbcglobal.net 619-929-1944

Just wondering as I'm restoring this 74 if putting a new aluminum radiator in ($200) vs re-coring the OEM one ($400) would have a negative effect on the value?

Looking for a set of four or five stock white spoke steel wheels from a '79 and later FJ40 or mini truck. In or near NC would be nice.

I recently replaced a leaking VCV near the distributor on my 1980 FJ40. The leak went away and the idle quality is better but the engine is running a little like the timing is off. I wonder what the suggested ignition timing is for a stock 2F running on modern 87 grade (10% ethanol) fuel and...

Can anyone suggest a good place or person to get a pair of the rear wheel center caps? New/Used I tried the local dealer and they are $52.00 each. I found a bunch of places selling them for the same price or a little better, plus shipping. 42603-60190 Is the part number I have.

Any one running these... BFG MK2 Thinking about pulling the trigger on them but discount tire won't mount them up. Thoughts?

Just installed a Gamiviti rack so I'm selling my factory rack. The finish has peeled almost completely off the front bar and is starting on the rear bar. Could be easily rattle canned to look new. Other than that it is mechanically sound. All of the hardware needed to mount and plastic covers...

**** ALL SOLD**** Thanks Have the stock front and rear springs off of my LX450 for sale, had 220k miles on them when they were taken off, and didn't appear to be sagging or anything. Anyone interested? I'll take $75 plus the ride for all 4. Open to offers.

Selling stock rear lights fj80 $140 great condition

Hello all! I have always followed this page and read and learned as much as I could about land cruisers as they have always been a passion of mine! I must say everyone on here is so nice and willing to teach and give their knowledge out, it is awesome! Well I finally recently acquired a 99 100...

Anyone have a stock draglink for a 1997 FZJ80 they want to part with, I bent mine wheeling ? I'm in Socal 92870. Thanks

I just picked up a 2000lx470 and part of my baselining is flushing ahc and bringing NP back into range. I just called a toyota dealership and a lexus and both said they are part of a national backorder. I was able to find some at a lexus parts site but the hazardous material charge was higher...

Stock 16" Rims: Asking Price 250+ shipping I have 4 of my stock rims for sale. I replaced these rims with Rock Warriors so these are sitting in the garage collecting dust. The Nitto Terra Grapplers have tread, but I would replace them. I have all the lugs that you can also have with them. If...

Pulled from a '93 FZJ80 with approx 110K mi. $250 for set, shipped.

Looking for one close to Denver if possible. Let me know what you have. Doesn't have to be showroom quality. Thanks, Scott

off '15 4runner w/ 5k miles Very good condition 2-3 1/2 inch small scratches, literally all I could find (pictured) everything else is grease $290 pick up in Valencia, CA 91355 Believe they can fit taco and 4Runner and land cruiser etc Pictured on a taco cuz they look good!

Hi All Doing a diagnostic 1FZFE teardown in preparation for a full and proper blueprint. Have done a bit already as you will see on my thread. Just finished detailed valve lash comparisons. 1FZ engine building and blueprinting During teardown I want to map all specs on this engine against...

Was out at Hidden Falls TX last weekend with some Jeep friends. Delighted with how well the truck did. It Creeped perfectly over some of the steps that the other trucks stumbled on. Funny how surprised the heavily modded Jeepers were, both at the performance and the fact I'd take it on trails...

Can you fit 33x12.5x20 tires on a stock suspension on a 2009 LC? Your input will be greatly appreciated. Thanks

I finished wiring up my factory tach today with the Dakota digital SGI-8E module. I couldn't find a definitive diagram in the search, so I posted this up. Easier than looking through a long build thread I decided the easiest way would be to splice into the wires on the vehicle side of the...