Hey all, i did myself a mischief and had 3 out of 4 bolts come loose on driveshaft on a long drive and managed to bend the rear output shaft on the gearbox. I was wondering if anyone could answer a couple questions i have:
1: Will the gearbox need to be dropped and stripped partially to remove...
I have vibration that gets pretty noticeable around 60mph.
It feels like it is in the back.
Steering is solid and no vibs in steering wheel.
Had this before I put new tires on and balanced.
I checked the drive shaft and found about twenty thousands run out on the barrel and the yoke is so...
Pro Tip of the day -
When measuring your drive shaft length for purposes of ordering a better one from Tom Woods, measure twice, maybe even three times. Use your best penmanship and make sure you can read your own damn notes. Then before pressing send on your order; go ahead crawl back under...
1985 hj75 troopy, Oz, manual h55f. Not sure if I should post in 60's section as most 70's posts are for newer than what I have.
Rebuilding h55f transfer. Have watched both otram and George's videos also referring to toyota manual and amayama schematic. Both Otram's and Georges videos are...
So I finally decided to pull the trigger and get a Tatton DC forward drive shaft for my LX450. I went with CJ Tatton given I heard great things about the quality of his work. When I tried to install and connect the CV to the T-case it would not slide into place. The CV’s circular holes would...
Been hemorrhaging money on this old Landcruiser lately, what's a little more?
Vehicle is a 1995 80 series with ~350k miles. Currently has ARB front bumper, ComeUp 9.5 winch, and MetalTech sliders. Rear bumper is stock, no cargo drawers or anything at the moment.
As for me, I've been building...
Front Drive Shaft off of 1996 Land Cruiser.
After going from 2.5" lift down to 2" lift the front shaft started a barely noticeable vibration around 70mph. I figured it might have been the u-joints settling into their new position so I installed brand new Toyota u-joints in this drive shaft. The...
Hi does anyone happen to have a junk or torn down a343 transmission from an 80 or 100 series? Looking for the output shaft. Please shoot me a PM if you do!!
Hey all, can someone post up pics of what you did for your SAS steering shaft? What parts did you use? I have both an 80 shaft and the 100 shaft. I don't want to reinvent the wheel and start cutting things that I dont need to.
Thanks!
First time doing this job on this truck and read the manuals, the threads, and watched the videos.
What I'm writing about is this part from the owner manual "re-torque nuts and bolts".
To me re-torque means losing up the nuts/bolts then torque back to specs - 88Nm. Yet, I did not see or read...
RARE FOR SALE, Original mechanical winch for LandCruiser from 1960 to 1984
Complete with winch, leveler, PTO, shaft and yoke.
It works and was removed from my 83 BJ 45.
It's heavy so freight shipping might be the only option.
Those are hard to find.
Asking $3000 + shipping
I will add this to the list of 'just when you think you've seen it all...'
Just pulled a standard H42 off of an F engine that I am servicing at the shop. Customer complained of growling noise when the trans was in neutral. I told him that most likely was the input bearing of the trans, followed...
I need to find this seal locally if possible, it's the seal inside the input shaft housing on an H41/42 (right behind the throw out bearing). Anyone have a part number that Napa would be able to reference?
Parts guy Shawn down where Cdan used to work, did a great job getting me hooked up with parts. One thing I always liked about Dan (and was willing to spend shipping on) was that I always got the right parts and I didn't have to know everything, unlike at my local dealer.
The techie part: I had...
Hi Guys I've just pulled my 2h out of the the 45 and almost ready to drop the 12ht in. I noticed I have a bit of play on the input shaft, both front to back and side to side. Just wondering how much is too much? does it rely on the spigot bearing? Also is the front bearing on the input shaft...
I have a H55 with 30k miles that decided to eat an Input Shaft Bearing this week...incredibly irritating
Given that situation, does anyone recommend a place to change the bearing in the Boston area? I'm in Franklin (close to Gillette stadium) but I commute for work
Looking for a place that...
I took the steering shaft off my 87 to grease the telescoping splines in an effort to get rid of the steering clunk like so many threads mention and since later FJ60's do not have the grease zerk. I removed it at the steering gearbox end and there is a rubber boot that covers where the shaft...