I unfortunately have to sell my truck. We're doing an addition to our house and the funds are needed there. Long story short, the timing belt blew and the truck needs some amount of work. I don't know exactly as I haven't fully investigated with a mechanic. As I understand, after speaking with...
Does anywhere sell this baffle between intake and exhaust?
I also had some good luck getting bolts out of the upper exhaust flange so I might go and buy a lotto ticket lol. I did chase the threads, I also need bolts. Also haven't finished cleaning the surface so. Not rebuilding the outside...
Hi All Im in Az (Copper State Cruisers) my father is in Wellington NV he is 85 otherwise we would do the water pump and belt on his 2011 Tacoma with the 4.0 v6 anyone have a trusted shop in the area he can take it to?
Thanks
Kyle
Just starting to restore a my 67 fj40. I have the fiberglass roof off and getting ready to repair the holes and dings. The outside is heavily weathered and the cloth and glass strands are exposed. Were these initially painted or gel coated? This has some remaining white coating in places...
Hey fellow Mudders,
Wanted to get some advice and direction for my FJ40 situation.
Last Friday we trailered my cruiser out to NE Oregon to get married. Cruised around Joseph/ Enterprise just fine the night before. Day of, ladies took my red truck (to keep their hair nice) and the dudes rode...
Hi,
I just purchased my first Land Cruiser, a 1992 80.
Is there any better repair guide for this vehicle than the one shown below? And is $100 a good price for it?
Thank you!
Video of issue
Hey there guys. I recently bought a 1991 Fj80. It’s my first land cruiser experience. When I bought it I missed a significant amount of rust on the body. I talked to a guy who said he has seen this problem before and suggested that I come here for help. I am in the New Mexico...
I finally started to tackle the wing window weatherstripping...figured 51 years so it's ok if I replace it a bit early. :)
Well I managed to break the stud under the driver window...anyone know of a repair or replacement source?
PS...I don't have a welder.
Son is having problems with 99 LC in Cumberland, MD. He said feels like LC loses power as he drives and noise is coming from front of motor. Had him check to make sure not in 4 low, center diff not locked, has oil, antifreeze levels are okay. Normally maintained. May be tensioner or idler...
I've been super careful and made it through a valve cover gasket R&R, intake R&R, Plenum R&R, IAC repairs, radiator hose replacements, belt swaps, water pump R&R, etc. and thought I'd succeeded in avoiding the fate of my past 80's and didn't break the dang nipple on the radiator. Then last night...
HI
I've tried searching with no luck, which surprises me. Tried different search words/phrases. Maybe I'm not searching correctly? If someone can post a link to any existing threads regarding my question below, I'd appreciate it.
I have a 100 series with the typical driver seat outside seam...
It's happened to me. I'm experiencing the dreaded 'brake failure', and I was hoping compassionate and knowledgable people on this list could help assure me that I'm doing the right thing to respond. (I trust my mechanic, but he's not the best communicator.)
Last week, I experiences the...
This is fresh this morning.
Got truck in the garage yesterday for fluid changes and left it on HI.
Took car out this morning and the freaking roof antena caught up on the door edge, bent the door and in the process was partially pulled out of the roof.
I have a trip comming up in 10 days so need...
Rehabbing front end of my rig. 313k miles.
Ran into this when cleaning up PS spindle for new spindle bearing, brass bushing, and seal.
Is the ID of the axle tube a critical spec? Thinking of just sanding down those ridges (somehow the axle chattered in the tube at some point??). Have a...
It looks like I tore my passenger upper cv boot yesterday. It flung out a bunch of grease. It’s torn at the small end first bellow. I’m tempted to clean it as best I can and wrap gorilla tape around it to try to keep grease in. It is driving fine with no clicking/issues. Any other ideas?
Salida...
Looking for a place in ABQ or close to that is willing to replicate and build me a new fuel tank or to patch this rusted tank (no reproduction units available.
i just picked up a 1989 62 series after years of wanting one. it has the typical rip in the drivers seat cushion and could use some new foam. Has anyone worked with a shop around KC and had good results? Thanks
For your reading pleasure and repair enjoyment, the following is now available for free download in the Resources section:
1998-2007 LX470 Collision repair manual (CR02X)
119 ppg, includes
General repair instructions
Vehicle lift & support locations
Locations of plastic body parts
Fit standards...
Hello all,
I have a 2003 Lx 470 which has developed a really bad bounce going over bumps and uneven payment. If anyone else has suggestions on what might be wrong that would be great as well.
I suspect it is bad globes so I purchased them to repair my self with the fluid. However, I tore my...