power steering

*Early 60 bolt pattern (square shape)* Bought another steering box which I had re-built by West Texas Off road. This I believe was original to the car and has a slow leak in the steering input shaft. Ideally would be used for a re-build/re-seal. $175 plus the ride. Think that these can fit in...

I just did my mini truck power steering conversion a couple weeks ago and wanted to tell everyone who doesn't have p/s why they should do it now. I've had my Land Cruiser for 5 years now, and if I had to start again, this would be my first mod. I started with brakes, clutch, electrical, etc...

I literally know nothing about power steering pumps so please dont roast me on the price. It's literally a WAG. When I bought my F engine a few years back, the PO gave me a box of parts. He had this power steering pump mounted to his '69 F engine. I took it off the engine as my rig is mostly...

Like the title says I'm looking for a factory power steering and a/c for my 83' BJ42 3B 24volt. Let me know if you have anything, I need to get some power steering on this rig and I would prefer to go with oem. A/C would be nice also, the weather is warming up in Texas. Thanks in advance

Looking for an 82-85 Truck or 4 Runner power steering gearbox for a conversion on my '75 FJ40. Pictured below.

No longer have a need for this pump since I don't have my 62. Pump, mounting bracket, pulley and lines = 100 + ship -Victor

Does anyone know a reputable person around Houston, TX who could install power steering in my 83" BJ42? Thanks

Would a bad or failing valve create hard, rapid left to right steering at low RPM (think parallel parking)? Recently replaced Timing/Idler/Tensioner pulleys and belts, rack is two years old (not leaking as far as I can tell), and steering is fine otherwise except for slow speed rapid left/right...

The paper clip is rusted pretty bad and leaking so the time has come. Going to go with the Derale Dual pass cooler mounted to the frame. This is the model I am going to go with: Amazon.com: Derale 13263 Dual Pass Aluminum Heat Sink Cooler: Automotive I want to eliminate the metal bends on...

does anyone happen to have a 1fz-fe power steering gear they are willing to sell. if so please let me know.

All: Any other options for this hose? 80 bucks seems a bit much for this hose. :S I assume regular pressure/bulk power steering hose can't be used because of the angles required?

I thought I remembered seeing someone on here that ran a FJ60 pump with a Saginaw gear. Can't find the thread. Would a FJ60 be enough? Would it be better to just use a GM pump? It will be going on a 79 block that has the mounting holes for a stock pump. A 60 pump would bolt up with the...

I'm doing the mini-truck power steering conversion on my '75 FJ40 and have gathered all the parts that I believe I will need. I've read romer's thread and it was very helpful. Just wanted to make sure I have everything before I start so I don't have to make trips to the parts store or...

I was working on my power steering. I replaced the HP line, pump, and the silicon for the lines that from the gear box to the cooler and from the cooler to the reservoir. I started it up to bleed the system last night and it ran awful. The steering was loose at first and then began to...

Looking to upgrade to power steering. Need the power steering gear and pitman arm.

I am getting close to pulling the trigger on PS. I found a rebuilt factory gearbox with the pitman arm and lines, but no pump. Is it best to go the factory route or opt for a FJ60 conversion? I am running 33" tires, BTW. I was told that the factory option still has the potential for a lot of...

Need the bracket that bolts to the left side of the block and holds the pump

I just wanted to get a new thread started regarding my current electric power steering build. First, Let me start by giving a HUGE THAANK YOU to KEN at Welcome to ePowerSteering.com He is setting me up with everything I need for the build. I will be sure to keep posted as we go. First of all...

I've been perusing the several write-ups on box rebuilds, but still have questions. I'm blaming my death-wobble on the 0.040" of backlash in my sector shaft (measured at the end of the pitman arm where the relay rod connects,) There is zero axial play in the sector shaft. Being hesitant to...

I am getting ready to make some replica power steering pump brackets for the FJ40 Land Cruiser. They will be based off of the original bracket and looks very similar. I wanted to see if anyone would be interested in them. The bracket will be for the 1979 and newer FJ40's that mount to the...