passenger

Years ago, when my kids were in car seats, I ditched the short jump seats in my 1977 FJ-40 for a Little Passenger front-facing bench seat. This seat is made as a 3rd row for various 2-row SUVs. It sits between the wheel wells on my 77 and bolts to the floor, through the floor supports. It...

Anyone in Central Florida area got an LC100 they are parting, with a good passenger front door? Prefer with door card, but I'm not picky, stripped door is good as well. Would go to Jax/Tampa or similar distance... Let me know... Thanks! Mark Orlando

What's the best place to source a rear passenger side fender flare and mounting hardware for an LX450? I've tried contacting a couple people who are parting out but haven't had any luck so far.

I need the passenger side assembly, not in need of the corner lamp housing.

I have two grab bars: 1) Brown FJ60 bar, complete with mounting gaskets/pads and screws. $100 2)Grey FJ80 (early years, pre95), complete with washers. $70

Hi all, I tried to fix my power seats and ordered new gears from gamviti. After reinstallation of the seat, It still won't slide... I've given up and want to just order new seats (don't care if it's manual) Anyone know where I can buy new seats? Thanks!

I just bought a grab bar from Cruiser Parts and I am disappointed in the finish they used to dye the grey bars brown. It looks like they just spray painted it with gloss spray paint. I can't bring my self to poke holes in my dash to install it, as in my it opinion doesn't match. This got me...

This thing under the glove box has been dripping lately. Seems to me like condensation. I live in Florida and my AC is on all the time. It's slight dripping that comes from here. I first thought that this is the issue that happens when the windshield is changed out improperly and it leaks at...

What the title says. Will buy either just a birfield with the lock ring or the entire assembly w/ axle shaft (will pay fair shipping). Just to be clear, I need the passenger side, non-ABS birfield. Thanks!

Hi guys, Car is a '97 FZJ80 with 155k miles Been looking through seat problem threads and everything points to caps and gears. My driver seat has the cap and gear issue (tilts up and down fine, but doesn't slide back and fourth unless I loosen seat bolts). I'll be ordering parts to fix that...

I have no power at the red/yellow stripe wire at the head light connection (highbeam I believe) on the passenger (right) side. I've traced the wire into the harness that is, I believe, still factory taped. From there I get lost... According to this wiring diagram, it connects with the red/yellow...

shipped to 92627 in Costa Mesa CA. Please message me if you have one you are looking to sell. Thanks!

Passenger side with end caps and some mounting clips. One small ding and some road grime. Still looks good. $60 + shipping. Located in Orange County CA. Can meet within reasonable distance.

Looking for a passenger side headlight for 97 LX 450

Lexus lx450 front passenger wheel sensor -- used $250. This is a $550 part aftermarket from Napa-- If your ABS brake is on then the sensor is bad. US Shipping only.

Looking for a decent spare tire carrier for passenger side. Could need some work does not have to be perfect. Shoot me a message with what you have and price shipped to 44216

In case you aren't aware, there is a MASSIVE recall due to Takata airbags exploding and killing or injuring passengers. This situation is much larger than most consumers realize, as the NHTSA is allowing the recall to be done in phases as the replacement bags can't be manufactured fast enough...

Hi All - Looking for a FJ60 passenger side inner fender in good or better condition. Shipping will be to Raleigh, NC at the local Fed Ex store. Please pm me if you have one you would like to sell. Thanls

Aftermarket, previously listed, but not currently locatable by me. Happy to delete this listing once SOMEBODY with better luck mining MUD can find me the old post. $165 plus the ride from Burbank. No PMs. Mark

Looking for a passenger side FJ40 factory tire carrier and latch mechanism to refurb/repurpose into a gas can holder. Condition not critical as I'll rebuild it, just need not rotted away. Thanks a lot!