motor

hey giys I just got a 1968 FJ40 1t motor with ~69,00 miles on it. Body is shot but frame appears to be in good condition. HAs some great parts (both axles, new brake cylinders and pads on one tire so I assume it is aon all four as the guy said he had brakes done, brand new radiator, seats are...

I'm slowly converting from an H to a 3B in my HJ45. The donor 3B's EDIC has the newer round type connector on it and my wiring harness is the older square type. Anyone have a harness available that they can clip about 6 inches off of with the plug on it? Thanks.

It turns out I needed a new rubber track on an FJ80 I sold, not a motor. Off of a '92 FJ-80. $20 OBO

Hey Guys, my AC does the 20s delay and resets to 75 degrees at startups. Checking the circulation flap, it appears broken (as it's loose to open and close). Is there a write up to remove the motor or access? I had read on another thread that some were able to put it in circulation mode and...

Working on a FJ45 wagon and trying to find a wiper motor that mounts under the dash. Its missing. Anyone have any ideas where to find one or perhaps a solution as to another one that will work? Thanks in advance!

Using a 24 volt 3B EDIC motor and a 12 volt 2H EDIC motor, I wanted to see if I could make a 12 volt 3B EDIC motor. Seemed physically the same with the exception of the arm orientation. So, I decided to perform a partial tear down to investigate. Here's what I've discovered so far:

1978 FJ40 The lower portion of my heater blower unit (that bolts to the passenger side firewall) is broken and missing a good chunk where it meets the louvers on the cowl. My fan motor works fine, not sure if anyone would part with/sell just the housing? Of course Id like one that is not...

the rubber or whatever it is coating on my blower resister is cracked and some of it is missing. Pic attached. Was working in both speed when I took it off. Should I wrap it in electric or harness tape or just leave it alone? Thanks.

Hi just finished rewire of my fj40 2F and amazingly everything works as far as dash, switches, lights etc. Used the EZ kit. My problem is that the motor does turn over but the starter says on after letting go of key. I obviously did something wrong. I was hoping someone would point me in the...

If you're using a WIX oil filter read this

Thought I would make a thread to give away my free junk because you guys are the closest thing to family I can pawn my garbage off to.

I searched and did not find one - Anyone have a good write up or video of motor and actuator replacement for a 2000 LX 470?

Looking for a good block or complete motor. Thanks Mike

40 delivered.

New to the family 1993 fzj80. I am in the process of diagnosing why I have no front heat. I have a solid temp reading on the dash. With the cable disconnected at the firewall the valve feels to move freely. When I removed the radio and disconnected the cable at the servo motor the cable moves...

So we are looking pretty seriously at buying a GX470 for Rachael (03-08 seem to be in the price range). They come with the 2UZ-FE, which I love, as they are pretty well known for dependability and hey, it's a Toyota, I should be able to work on it when anything goes south on it. Quick...

Selling 4.5L straight 6 1FZ-FE enigine from 1996 FZJ80. Bought it from a guy that did a V8 swap, and he said it was around 250k when it blew the head gasket at the #1 cylinder. Originally wanted to rebuild it and use as a donor engine but never got around to it. Comes with a lot of accessories...

I have a NIB Denso blower motor resistor for a 24V Cruiser. Toyota part number 87138-60150. $60 plus shipping. It may take a couple of days for me to ship it, so you'll have to be patient.

Looking for a used OEM 60 series front blower motor and looking to pay around $50 plus shipping to FL.

Toyota recommends 0w-20. In other countries thicker oil has been recommended for older land cruisers. In the US we had a 5w-30 recommendation for the 1fz-fe when other parts of the world had thicker recommendations. Historically the land cruiser has been easy on oil with prior engines. I'm...