master cylinder

I recently replaced my rear drum brakes on my '75 FJ40. The front has disks and the PO recently had new shoes fitted. After flushing the whole system I kept it on the jack stands and ran the engine in 2WD. The wheels turn, but the brake pedal goes straight to the floor. Looking at the master...

I have front disc brakes on my 1980 FJ40 and rear drum brakes. But the braking is horrible, any hard sudden braking results in wheels locking up (i believe the rear) and the car just continues to slide forward. Doesn't necessarily have to be at high speeds either. I know from my Datsun when I...

Firstly, thank those who answered my thread a few days ago about the type of master cylinder I needed. I recently bought a 96 FZJ80 VX limited imported 102,000km (63k miles) from Japan. It's in pretty incredible condition; there are a few minor things I already took care of noted in the...

So I've been chasing brake issues for a bit now. I my new rotors warped within a few thousand miles, after I had rebuilt the front rotors which were really crusty. So thinking the calipers were still sticking I bought rebuilt calipers and had the rotors turned. Everything was good for another...

I have a 1996 FJZ80 imported from Japan (JDM, RHD, etc, etc), it's fantastic! I hate to start another thread on the Spongey brake issue (I've read so many), but as I follow the FSM, I have run into a dilemma. The Brake Master Cylinder has 2 bolt holes onto the booster instead of 4, which...

For sale is my 100 series' original 07/1998 manufacture date brake master cylinder with booster in very nice condition. While I had it out doing my diesel swap (the bore was extremely clean without scuffs or other blemishes) I replaced the piston assembly with brand new Factory parts and it went...

Hello Masters of fj40 world. Beginner here. I bought a gorgeous '71 with the original 1f. The seller confirmed he had some resto work done, Including the trans/transfer and front axle out of a '76. Gave him the 4 speed, and front disc brakes. I have had a weird intermittent "dump" of Dot3...

Long story short, I had the typical alarm and dash light up in my 2002 100 Series with 155K miles. The work was done by a toyota specialist garage that I've been going to for years. They replaced the master cylinder with a brand new unit and are still getting the alarm & dash light up. They...

Ok, we need to either rebuild the Clutch Master & Slave Cylinder or buy a new one - any recommendations? - I don't know if they make a rebuild kit for the slave cylinder. - Is it better to buy new, if so, where do you recommend. It is funny, I was on CR and the Clutch MC for a '75-80 is $45...

Hello, I am working on a truck that I received in boxes. This is my first go round with the FJs. I have a new master cylinder, the dual piston model with dual reservoirs. I also have new hard line kit. The hard lines could hookup either way. Do the rear brakes engage first or the fronts? I...

Hello, Does anyone know the part number to the spiral brake line that connects to the brake master cylinder? I ended up rounding one of the heads :/ 1993 land cruiser Thank you!

Hi all, I recently had what I thought was a blown out master clutch cylinder. I ordered a new Aisin CMT012 from Rock Auto and installed it. I tightened it down and went to bleed it and noticed it was leaking terribly from the fitting. I took it back off and compared to the old MC and noticed...

Good OEM master cylinder from a 1993. $60 plus shipping

$150 plus shipping to your AO Will need full rebuild, Techstream codes pulled and included in photos photos

00-02 Toyota Land Cruiser/LX470 - ABS PUMP - MASTER CYLINDER - BOOSTER - ACTUATOR w/VSC/TRAC Part# #47050-60042 Purchased as a spare for my 2001 100-Series Land Cruiser. Remanufactured and tested by eNet Auto Parts. Selling below my cost to fund another project. $750 + Shipping in U.S. to...

Hey all, I recently took my LC100 with 247k miles to a local 4x4 repair shop to replace the Brake Master Cylinder. I've had some long travel-squishy brakes so I figured to be safe. I'm still new to owning a rig this old and am trying to learn on it but I felt like that was slightly out of my...

Good morning! In my efforts to put my 02/1999 Elsie back on the road, I sourced a brake booster assembly to replace the bad one I took out 3-4 years ago, and even though it was for a "1999", it doesn't fit the bolt pattern on the firewall. The replacement booster has a bolt pattern of...

Hey all- '06 spongy pedal, slowly goes to the floor - no leaks on brake lines, or at calipers, and not losing fluid in reservoir. No screeching pump, ABS or VSC lights. I'm guessing master cylinder seal(s) leaking. I could only find a MC rebuild kit for the 03-04 years, so I bit the bullet...

Hi, I recently replaced the booster and the master cylinder and manually bled the brakes on my 87 FJ60. I dialed in the booster rod several times to get it right so the brakes don't grab when coasting to a stop and the pedal feel is good. After driving about 4 miles for an errand, I got back...

OK, 'Mud community, I've searched & read for the last few YEARS and still haven't come to a real conclusion on this. Hopefully somebody here can FINALLYclear some of this up. I have a 1991 3FE FJ80 (Disc/Drum brakes, w/o ABS) However, I have a Full Float disc brake E-Locked rear axle, from a...