manifold

For sale, make an offer PM no cracks, good condition.. just need to be cleaned

My flapper was loose on the shaft so I pulled it apart. Does the bend in mine look correct? I temporarily re-installed the flapper in the same orientation I found it. This would be cold Here's hot

I accidentally bought intake exhaust manifold for a 1975-1978 2f engine and not the 84' fj60 2f. Looking to sell this one will ship at your cost. Comes with Bolts and Carb Studs. Gaskets are removed and need replaced (but your probably doing this anyway if you have your cracked one off). No...

So i bought what i thought was a 2f FJ60 manifold. Its darn close but putting side by side and trying to use my block off plate they are clearly different. Any Idea what the Left on is from? International FJ60? Also its for sale since i cant use it anyone need one of these? Intake manifold by...

The Toyota parts diagrams appear to list 2 parts that seal the joints of the 3 piece exhaust manifold for the 2F. Ring gaskets for 2F 3 pc manifold 17151-61010 Gasket springs for 2F 3 pc manifold 17152-61010 I see 2 parts that look like small piston rings in grooves of the end...

I'm rebuilding a 3F motor and in the process bought a "full" gasket set believing all gaskets needed would be included. It does not have whatever it is that seals the two halves of the exhaust gasket together. In my limited experience of engines I have never seen a setup like this. Local parts...

I'm rebuilding a 3F motor and in the process bought a "full" gasket set believing all gaskets needed would be included. It does not have whatever it is that seals the two halves of the exhaust gasket together. In my limited experience of engines I have never seen a setup like this. Local parts...

Hi, Do I need to remove my injector lines to replace the manifold gaskets? If so, will the engine restart by using lift pump or will I need to have an injector pipe open? Dave

Since installing 3FE exhaust manifolds and losing the 2F exhaust I've noticed that the engine is more prone to rough running when cool to cold. Once the water temp reaches 150F the engine smooths out. The stock exhaust has a provision to warm the underside of the intake as soon as the engine...

Found my intake cracked today. Anyone looking to sell a intake manifold or complete manifold? Let me know.

Got my intake etc off today it is cracked right down the center...awesome Does anyone have a spare intake they are looking to sell or trade?

When I bought my 60 it had an exhaust leak. I was able to quickly identify that it was leaking at the connection between the manifold and exhaust pipe flange. No big deal, I thought. After me swapping two gaskets and taking it to a local muffler shop (a good one), it turns out that there are...

New in box Doug Thorley Headers. $710 new. These are in pristine condition, includes gaskets. Box has storage wear. Purchased to replace cracked right manifold, took easy way out and went stock. $550 free shipping in lower 48.

Hi all, I'm trying to track down a ticking noise that comes from the driver's side after the engine has warmed up a bit. Follows the rev range. I assumed it was a manifold gasket or a cracked manifold. I removed the manifold this weekend and didn't see any cracks. I made a Photobucket album...

Hello, I have the following for sale, prices do not include shipping. 1980 FJ60 Parts Manifold Set - $200 OEM Carb - $100 Air Rail - Less than 300 miles - $200 Smog Hoses - $25 each Chrome hubcap set - $100 shift knob - $10 Shift fork and new throw out bearing - $75 New Clutch plate - $40...

Hi All, My FJ60 passed California smog last weekend under the condition that I install the little bracket that connects the Hot Air Idle tube to the intake manifold. I need to bring it back to the technician and show him that I have it installed within 2 weeks. I ordered one from...

My truck is running like a top, idling smoothly at ~650 rpm, but after doing the 'lean drop' method I've got the idle mixture screw turned nearly all the way out. Doesn't seem right. I have to believe this open vacuum port on the intake manifold, next to the brake booster line, is to blame...

I discovered that my intake manifold is cracked ( already welded once) so I'm looking for one in good condition or ideas on where to find one. It's a 1985 FJ60 2F Engine. Located in ABQ New Mexico. Thanks

I bought all this years ago ang have never gotten around to doing anything with it all. I do not have the turbo or any other parts, just what you see. 17141-58011 Manifold 17167-58012 Heat shield 17168-58041 Heat shield 16331-58030 Water outlet housing All these parts are new OEM. The sale is...

Need a down pipe from an '80-'87 FJ60. OK if it's missing the air injection tube. Price plus shipping to 55082. I've got a shelf full of parts - let me know if you need anything and maybe we can work a trade. Thanks! Kevin Lillopad@gmail.com