fj40

Selling a pair of driver seat mount brackets off a 69 FJ40. Sold

I need a set of 12 backing plate bolts for the 70s FJ40 rear axle. These bolt the brake backing plates to the axle housing. Apparently they have a special shaped head. Shipping to 28461. Thank you.

I'm finally at a point to start this project. Picked up a 67 FJ40 about 4 years ago. Got it for a good price and the seller even delivered it. The pic on Offer Up.

I converted my 1982 to oem factory power steering . Missing heat shield and brackets.

They have some rust but still good enough from being OEM and hard to find. They will go to the scrap first week of December I am at 11787

I have a 1978 FJ40. Where was this located on the vehicle? What does it control?

Hello. Been searching through forum for similar problem and found close but not exactly my issue….. tested starter, new battery, and yes it has gas:) and will not turnover. It has sat for a month. Jumped it and let it run for about 5 minutes. Drove it 5 blocks from the house and it died...

Searched and read through several threads but still running into some trouble. Replacing some Jeep style tail lights previous owner had on with OEM tail lights. The Jeep style lights have three wires. OEM just have the two bullet connector wires. I was under the impression the solid green OEM...

I have a 1970 fj40 with F engine. After reading a number of alternator threads I have purchased a 1990 dodge Monaco alternator. Truck has basically no wiring, just the 4 wires to crank and run so no old wiring or reg to work around. What is the pinout on the 4 terminal plug?

Selling a hood spear off a 69 FJ40 Sold

Need help getting my 76 Fj40 back on the road. Is there any mechanics in the Raleigh NC area to help get my project back on the road?

Does anyone have one of these lying around? My front heater is missing the selector lever and indicator. I need the pieces circled in red.

again, nothing revolutionary here, just some before and after. not too bad but tired and overspray from the last owner

Looking for just the motor side for my 1970 FJ40. Will consider complete and non-working as long as the drive gear that engages with the motor worm drive is good. I'm based in the UK but can provide a postal address in the US if yu're not able to ship internationally. Thanks :-)

Howdy Cruiser heads! I am wondering if these shocks will fit. They seemed to be the correct shock, although not OEM. Another forum suggested this was a comparable shock to OEM and they were a good enough price to consider going with the KYB. However, not if these don't fit. Measuring the frame...

All prices plus shipping. Bundle to save on shipping Free with purchase - Red reflector pair $10. New Ignition switch. Not OEM. unknown year. 0.724" diameter so it should fit roughly a 3/4" or 19mm hole. $15 for both: patina early front signal lens (left in pic) and almost new early front...

Hello, I am looking to buy a VTV-vacuum transmitting valve that is Toyota part # 90925-01006. I need the red top with black body if anybody is willing to sell theirs or has an alternative that would be great. Mine broke as I was replacing all my vacuum lines.

Still available: Early steering brace $5 Black Friday Deal Free Master Cylinder (Pbr) $30 Black Friday Deal $10 Unknown Master Cylinder, free with any-other purchase....FREE Carb Cooler (not FJ40 I believe, no squirrel cage) $40 Black Friday Deal $20 SOLD: Ambi Door access Plates: $10 each...

Got a '73 FJ40, and I have seen somewhere on Ih8mud that someone had used a 2.5" shopvac hose to make a defroster duct. Anyone done this? If so, can you expound on what you did or if you have pics.

Selling a early grab bar off a early to mid 60’s fj40 Early grab bar sold