engine

Good running engine, 210k miles, valve seals a bit dry, burned 1 qt of oil every 2000 miles, ran great when pulled for upgrade $1500 takes it, prefer pickup but may be willing to ship

Hi guys! I'm just wondering what RPM are you getting when at highway speed like 120 kmh? My 73 with 285/75 tires is almost at 3K RPM. From there it feels like the engine likes to be on that range. I can pull and keep up with traffic easily and its happy to go 140 kmh/3300 rpm. When I got...

I have a running 3FE engine and transmission 242k miles, no smoke and transmission worked great. Out of my 91, (doing an LS Swap) mostly complete, no electrical harness and missing some sensors. free for pickup in Marysville, WA.

My 2005 reached 200K about five months ago so I had the following items replaced, all OEM parts from Toyota that I personally picked up. -timing belt -drive/serpentine belt -tensioners -pulleys -water pump -radiator -fan clutch -fan bracket -gaskets/seals/related hoses -thermostat -lube all...

Looking for short block but will consider a long block. Will be rebuilding but still preferably no significant damage. East Tennessee. Closer the better. 1fzfe obd1

Here’s one for the DIYer.. Broken H55f from a 1988 JDM HJ61. 2F / H input shaft (although this input shaft is junk so you could put whichever version you want in) Input shaft is bad and counter shaft is bad. Would recommend a full rebuild kit as well as those parts. I can also sell a new OEM...

Ceramic coated , planed/machined ready to install 3FE exhaust manifolds ready to install $500. Shipped to lower 48. Note: EGR port has been welded shut and shield bosses have been removed. I was going to use these on a 2F but couldn't get machine shop to thin the flange to match up with 2F...

I finally got to replacing my engine mounts, but on my first test drive a fuse link popped (battery terminal - black to white). Got the new fuse link in today, but there is a nasty short. Started disconnecting my ignition switch and alternator, but still no luck. I have removed all the fuses...

Closer to Louisiana the better. Anyone got an A340F sitting around they don't need?

I’m putting my engine back together, (1994) and Im waffling on putting the EGR back on. It’s disabled either way, but I’d love to just put the block off plates on the head and intake for a number of reasons. Since we are all over 25 years now, the reg says we get just a “safety” inspection, but...

So took my FJ40 (1982) for a cruise around Toronto. At a stop; I noticed an oil leak; it was a little more than just a few drops.... so it was concerning. Traced the oil to the 2nd spark plug. At least, that was the only wet oil stain that aligned with the oil on the floor. Checked the...

=========== NOTE - These are not mine, contact the seller via the Craigslist Ad ================= 1971 Toyota fj40 landcruiser. Chevy 350 engine , turbo 350 automatic trans, 4 wheel disc brakes, ausi rear locker, 9000 lb winch, power steering tilt column, tow bar, run great pink in hand...

Parting out a very interesting 96 (build date Jan 96) 80 series. Will list the major parts in their respective categories here on MUD- if anyone is interested in anything specific please contact me via email shmukter@pa.metrocast.net Truck has 166K miles and was a daily driver until rust...

I have a 3FE long block I need out of my way. Came out of an early 88 based on the numbers. I kept the head for my future 2FE project. I know nothing about this engine. Free to anyone that picks it up in Spokane, WA, though I could be haggled with to accept more: I have a hoist to load. Has the...

Can the front drive axle be removed on 92 FJ80 to test on Dyno with a LS swap without harming the drivetrain or transfer??

Hi, I have a 92 3fe and I am struggling to find why my engine stumbles. My emissions reads to much carbon monoxide......92 over 25. It came down from 150 over 25. I am saying is it should be 25. Denver Colorado The cruiser has a a few bumps in the idle that I can't figure out. It drives...

I've got a complete B engine with bellhousing and clutch for sale. Assuming it came from a BJ40 of some year, it is a European engine. I got it for a project a few years ago, purged the air and started it right up with no issues. I then pickled it with transmission fluid and its just been...

Greeting All: I need to get some 2F engine number for US Spec Cruisers built in Jan of 1982. My engine number matrix pictured below has starting number for 1982 that is very likely an error. I'm guessing the numbers were transposed somehow. I would like to correct it. So if you have a Cruiser...

Would anyone know where to find the engine number plate on a 1988 LJ70 LC? The VIN number plate is on the back of the engine compartment, but I am having trouble finding the engine number. Thanks

I’m in need of a useable 2F camshaft. I had mine reground by Delta Cams, and we’ve been having an issue with one of the lobes having a considerably smaller base circle than the rest. It’s causing major difficulties with valve lash and noise. Welding the entire lobe isn’t really an option due...