My brakes are super crusty. Looking for some clean rear drum backing plates and front disc backing plates. My truck is a 1994 FZJ-80 with a SF rear axle.
4704460060 LH Rear Drum Brake Backing Plate
4704360110 RH Rear Drum Brake Backing Plate
4778160100 RH Front Disc Brake Dust Plate
4778260100...
Hey folks, the ABS and BRAKE lights just randomly came on when I started up my 2001 LX 470 today, out of the blue. I've had the car for six years and neither of those lights have ever come on before (except BRAKE when the parking brake is engaged, obviously). It has 191k miles.
A little...
I have a master cylinder/booster with a brake proportioning valve as per the first picture in this thread.
If you have a 1987-89 non-US 60 series with front disc brakes and no rear load-sensing proportioning valve, could you please tell me which output from the proportioning valve goes to the...
I'm in the process of rebuilding a (non-North American) 1989 BJ60. The vehicle was originally equipped with drum brakes on all wheels, so never came with a brake proportioning valve. I am adding a year-correct, factory original brake master cylinder, dual-diaphragm booster and proportioning...
Hi All - I have a 1996 LX450 and a section of the hard brake line that runs from the front to the back blew out. It is the area under the car that lines up with the front section of the rear leaf springs (hopefully that makes sense). I am in the Lake Tahoe area and my mechanic says they have...
Sold my 100 and never got around to installing. Slee 100/ LX470 braided brake line kit. NOTE: This is only for 98-99 years. Slee part STF1088.
$125 shipped firm. These are brand new un-opened.
Trying to confirm my suspicions and thought I’d check with the pros on the forum incase there’s something I haven’t thought of.
I have a 73 FJ40 with OEM power brakes.
Under formal driving conditions the brake pedal is very soft “squishy” on the first press and then you can pump it a few...
The LSPV on my ’96 USA-spec was dripping and I figured I’d install a replacement, not delete.
I got everything but the rod bolted back together only find that the blueish plastic forks that form a slot for the rod are at a different angle than the old one. See photo.
Do I have the wrong part...
I'm looking to buy a 13 LX570 with what seems to be a braking issue.
Whenever the brake pedal is pressed while the truck is moving there is vibration/shudder throughout the entire truck and steering wheel. the sensation is almost like the calipers are clamping then letting go in quick order...
I understand the process for the most part, but I'm confused about the 5th bleeding spot (according to Hayes manual), the master cylinder. Do I need to take the cylinder out of the truck to bleed it (bench bleeding I've seen it called). How would you bleed master cylinder? Also in my research I...
It's happened to me. I'm experiencing the dreaded 'brake failure', and I was hoping compassionate and knowledgable people on this list could help assure me that I'm doing the right thing to respond. (I trust my mechanic, but he's not the best communicator.)
Last week, I experiences the...
Hey, i have problem with brakes on my LC 2003, 4.2 after reflush brake fluid.
Problem is that brake pedal is little bit soft. And what can be see the most problem is when you stop on redlights, using brake pedal. Car will move after few seconds. It will like release the brake. When you push...
When compressing the pistons to install new pads, some of the boots got folded out/unseated. I tried sticking it back down but couldn't get it all the way. Perhaps I need a different tool. The best thing I could think of that I figured wouldn't damage the boot/seal was the small red tube that...
I just had the rear wheelbearings done and had the shop do the park brake shoes while they were in there.
The park brake was well out of adjustment when I picked the vehicle up but took it home with the intention of bedding in the new shoes and adjusting it myself (I've always been successful...
Hey all, been awhile since I have been able to spend time on the ‘net’. That said, glad you folks still here. As many may recall…still relatively new to the Landcruiser world and continue to learn and scratch my head.
Enjoy reading and the encouragements I have received. So……. here’s my...