60 series

I'm looking for a manifold that fits the airconditioner compressor for a Denso 471-0204. This is supposedly an OEM part off of a 60's series, although I have put it in an HJ47. I have a working compressor, but no manifold to be able to connect the rest of the equipment. Any assistance would...

Hi All - Have any of you converted your 60 series steering box to the 80 series? Then, has anyone further upgraded to the 105 sector shaft and pitman arm? I have a 80 series steering box on my 60. Wondering if it is worth the $600 to upgrade to the 105 sector shaft and pitman arm? I do not...

I would like to genuinely thank all those who have viewed, installed, and supported my decals here on MUD. I truly appreciate you because I love these trucks and you are part of them so its a special feeling to be part of your projects, community, etc.... I am now offering 'practice' decals...

Looking for a decent Fj60 frame or roller. Located in northern Florida but willing to travel or ship over , TiA

Wanted!! 1986 fj60 seat covers in decent condition. Color and pattern like the one below. Let me know what you’ve got! Thanks

I aquired a 1984 60 series with a chevy 350 TBI the 4 speed tranny with a ranger III overdrive. it is noisy even after changing oil in tranny, transfer case, and overdrive unit, also acts like sycros are needing replaced, parts as far as I know are no longer available for the ranger and...

Figured I’d throw these up here in case someone wants to move a shackle mount, undo a shackle reversal or upgrade their 40 to larger 60 bushings… Full set of 60 spring and shackle hangers cut cleanly off the frame $150 for all plus shipping Or $75 for each end

I decided to start a new thread since I am finally done and have completed the final prototype. 12 gauge CR steel. I can build this in different air flow designs also. This kit is available now for preorder at $1250.

Planning on ordering a set of sliding windows from Australia and a few vendors have quite a few sets. They were saying the freight on multiples wasn’t much more than ordering just one. Was wondering if anyone else wanted a set?

Dana point Ca ready to drive whenever I need. Thanks all!

Have an 86 60 series---i've read and noticed some of you have front seats from BMW or other rigs--I'm looking for leather, heated front seats and a matching back seat that folds down. I'm thinking of possibly 4Runner or 80 series seats but haven't seen anyone do that here so guessing they don't...

I'll do all posts with pictures. When sold, that ad will be erased. All prices are plus shipping via USPS. 16333-61110 2F Thermostat Housing that fits FJ60 or 8/'80+ FJ40. $175

Hey guys I am looking for a late 60 series clutch fork. Thanks, Carter

Wrapping up the design and manufacturing details on the ORIKAWA 60 Series Center Console this month. To maintain a reasonable price-point the initial run (at least) of consoles will be done as a batch. Pre-Order will open in the next two weeks with units expecting to ship in October. Final...

Wrapping up the design and manufacturing details on the ORIKAWA 60 Series Center Console this month. To maintain a reasonable price-point the initial run (at least) of consoles will be done as a batch. Pre-Order will open in the next two weeks with units expecting to ship in October. Final...

Fj60 arb bull bar wanted. Near Austin or in Texas preferably. Preferably used.

- Includes left and right front bucket seats for FJ60/FJ62 Toyota Lane Cruiser (blue/grey). - Passenger side includes floor mount. - Seat bottoms reupholstered 2018. - Headrests not included. Set: $600.00 Driver side: $300.00 Pass side: $350.00 Thanks!

Looking for a good used condition 60 series spare tire carrier/winch. I'm in Canada so must be willing to ship up North. Shiny new one pictured but it doesn't need to be that pretty.

I have a master cylinder/booster with a brake proportioning valve as per the first picture in this thread. If you have a 1987-89 non-US 60 series with front disc brakes and no rear load-sensing proportioning valve, could you please tell me which output from the proportioning valve goes to the...

I’ve got the FSM and a multimeter… but… physically how do you test the sucker? Just jam the probes behind the wires? Get thinner probes? Any help would be appreciated. This rig keeps throwing me curveballs :)