3fe

Need a thermostat housing pair (upper and lower) with no rust or corrosion issues. Thanks!

I am pulling the 3FE from my '89 FJ62. It is all original as much as I can tell. It does have some leaks. 310K original miles, again as far as I can tell. Trans was rebuilt by PO and has ~1,500 miles on it. Comes with ECU, harness etc up to the transfer case. That is staying with the new motor...

First off, this is my first post but ‘Mud has been a massive resource for me these last few months. In the last year I acquired a 92 FJ80 and since I’ve slowly been building him (“Lando”) up. So far: water pump, belts, hoses, power steering pump/pulley, PCV/grommet, tires/wheels (Duratrac...

Out of nowhere the rig is lagging and dying if I give it much gas. If I stop for a while and start again the rig gets up to speed fine, albeit very weakly, but if I have to give it any more gas for a hill or anything, I'm back to fluttering until I'm going 5 mph again. Its hot today. Any helps...

What 1 by cruiserland80 posted Jun 20, 2017 at 7:28 PM What 2 by cruiserland80 posted Jun 20, 2017 at 7:28 PM Can any one tell what this is?

Hey Everyone I wanted to see what you guys recommend for what gearing ratio I should go with. I have a 1991 Land Cruiser that has the 4.0 3FE EFI with stock small tires (I think they are 31') I noticed when I would drive uphill to Tahoe from the valley in California on freeway it would be...

I have an interesting problem that just started on my rig. 1989 FJ62 190K+, stock engine upgraded H55 trans. I noticed the coolant level down a bit and some coolant dripping down the front of the engine a while back. Decided it was time to tackle the dreaded water pump on Rusty. Ordered up the...

I am installing the front end plate on my 3FE. Should I put any gasket treatment or something similar on the gasket between the block and the front end plate? I was going to use some Toyota Black FIPG but I wasn't sure if that is what is normally done. What is the best way to install the gasket...

So long start short I my car just Rieves and stalls when starting unless I absolutely floor it and hold the rims at 3000 for 30 seconds, also found this vaccum leak, help!!!

Can I get an FJ80 / 3FE owner to tell me what color their 2 wires are going down to the OD sensor on the driver's side of the tranny, and then maybe tell me what color they mate to at the plug where it enters the wiring harness? When I pulled my motor, that little 2-wire plug on the back left...

Hi, Front main seal was leaking. No noise before. Replaced front main seal and installed a sleeve ...started engine....squeal ....stopped engine ruined crank pulley and cover. Replaced seal ,crank pulley with sleeve and cover. Started engine..squeal .Immediatly shut of engine .Pulled cover and...

I was going to try to restore a 136,000 mile '88 FJ62 I acquired, but the interior is much less complete than I had hoped, and somewhere along the line, someone removed the spark plugs for an extended period of time, causing the bottom of the engine to require cylinder work (why someone would do...

My distributor coil just turned into a fuzz ball.The rest has had me worried for a while. Anybody got a 3FE distributor in good shape? Please message me!

Hello Everyone, My apologies for not being more proactive with posting (especially pics) as I have had a lot going on in life. I have a 1991 Land Cruiser with 333,000 miles on the clock and have put 250 miles on the tank since purchase. I have replaced the battery, the alternator looks to be...

This is for some deeper discussion for me as I under stand how to do it. and have the desmog guide for the 3fe. 1. what I know, the 3fe is designed to run desmoged, I will get better power, smother running, and possibly better over all mileage but this is debatable and not really important. 2...

I'm trying to track down all the hoses and any relevant clamps, here's what I have so far: 1) 87245 60480 Hose, Heater Water, Inlet B; Hose, Heater Water, Outlet C 2) Gates Green Stripe/Napa Gold Stripe or equivalent 5/8" (hose clamp 87124-28030 X2) 3) Gates Green Stripe/Napa Gold Stripe or...

I'm replacing the cobbled up wiring for my 1978 converted to 3FE. Hopefully when I get all my questions answered, this can be a resource for others tackling this conversion. What I know for now is that the engine harness goes in with no modification. I'm trying to modify my cowl/firewall harness...

Can I rebuild the PS pump, or do I need to just replace it?

I looking for this bracket and sensor. I threw mine away a few years ago and want another.

Hi, I'm experiencing hesitation at low speeds, clears up in 2nd & 3rd, then at high speeds it stumbles when dropping into 4th gear. My idle is a bit high in park, and drops to 650 in gear. At a stoplight, in gear, it stumbles. Could this be a fuel issue? A buddy of mine swears it's the fuel...