3fe

Part #'s: 25870-61020, 25620-61120 Location of seller: Edmonton, AB Willing to ship: YES New or used part: USED Price: CAD $75.00 Description: Removed the EGR Assembly from my 1991 FJ80. This includes the EGR Valve, EGR Vacuum Modulator, and the EGR Pipe. Does not include gasket or mounting...

SoCal NO SHIPPING! RUNS REALLY GOOD Cyl Head appears to be recently changed. This is in a 1991 FJ80. Odometer shows 131,000 but this is doubtful. Engine runs good. You are invited to test it yourself, bring a mechanic etc. ECU is extra. Engine sold without starter, alternator, Air Flow...

Hi all, yesterday after driving my '91 around for a while, I stopped for about an hour and when I started it again, the RPMs at idle jumped up to 1600-1800 RPMs. Prior to this, it had been running fine and idling around 650 RPMS. I initially checked to see if throttle cable was stuck, but it...

SoCal, Los Angeles area. ABSOLUTELY NO SHIPPING! I bought this car for body and axle parts, and test drove it. Engine is in the car now so you can test it for yourself. Head has been redone recently. Odometer shows 121,000 miles but is doubtful that this is true. My mechanic says it is...

Doing a conversion to my 1988 FJ62. Just took out the 3FE engine and A440 trans... both running well. Original miles on engine 207K. Transmission was rebuilt at 179K miles, has 28K miles on it. $2K for both. Ships from Everett, WA.

SoCal Parts are from 91 and 92 year models Shipping is extra: E brake cable $20 Air Switching Valve (Vacuum Switch Valve) 25710-61031 $25 Ignition Coil $30 Smog Pump $30 Radiator Side Brackets $40 pair Heater Valve (on Firewall) $27.66 INCLUDES SHIPPING US AC - Heater Control Module (Mounts in...

200k Selling to get something more fuel efficient. Open to trade for AWD with decent fuel economy. Volvo XC70, highlander, forester, ??? Has no major issues. Minor issues include -oil drip leak from oil pan gasket, but not enough to require top off between oil changes -needs new windshield...

hey all, trying to fix an issue I've had since I got this truck in January. 1991 3FE, desmogged. 200k miles. Currently getting 10 ish mpg with top freeway speed at 80 on dead flat with no wind. Recently checked/replaced vacuum lines and rubber throughout, rewired EFI relay to successfully...

Hi everyone I need some help. I'm pulling just the engine on my 80 (3FE). Ive been trying to pull it for weeks and just can't get it to slide off of the bell housing. The two are split a few millimeters but they just don't want to separate. All of the trans bolts are out. Motor mounts off...

Need a thermostat housing pair (upper and lower) with no rust or corrosion issues. Thanks!

I am pulling the 3FE from my '89 FJ62. It is all original as much as I can tell. It does have some leaks. 310K original miles, again as far as I can tell. Trans was rebuilt by PO and has ~1,500 miles on it. Comes with ECU, harness etc up to the transfer case. That is staying with the new motor...

First off, this is my first post but ‘Mud has been a massive resource for me these last few months. In the last year I acquired a 92 FJ80 and since I’ve slowly been building him (“Lando”) up. So far: water pump, belts, hoses, power steering pump/pulley, PCV/grommet, tires/wheels (Duratrac...

Out of nowhere the rig is lagging and dying if I give it much gas. If I stop for a while and start again the rig gets up to speed fine, albeit very weakly, but if I have to give it any more gas for a hill or anything, I'm back to fluttering until I'm going 5 mph again. Its hot today. Any helps...

What 1 by cruiserland80 posted Jun 20, 2017 at 7:28 PM What 2 by cruiserland80 posted Jun 20, 2017 at 7:28 PM Can any one tell what this is?

Hey Everyone I wanted to see what you guys recommend for what gearing ratio I should go with. I have a 1991 Land Cruiser that has the 4.0 3FE EFI with stock small tires (I think they are 31') I noticed when I would drive uphill to Tahoe from the valley in California on freeway it would be...

I have an interesting problem that just started on my rig. 1989 FJ62 190K+, stock engine upgraded H55 trans. I noticed the coolant level down a bit and some coolant dripping down the front of the engine a while back. Decided it was time to tackle the dreaded water pump on Rusty. Ordered up the...

I am installing the front end plate on my 3FE. Should I put any gasket treatment or something similar on the gasket between the block and the front end plate? I was going to use some Toyota Black FIPG but I wasn't sure if that is what is normally done. What is the best way to install the gasket...

So long start short I my car just Rieves and stalls when starting unless I absolutely floor it and hold the rims at 3000 for 30 seconds, also found this vaccum leak, help!!!

Can I get an FJ80 / 3FE owner to tell me what color their 2 wires are going down to the OD sensor on the driver's side of the tranny, and then maybe tell me what color they mate to at the plug where it enters the wiring harness? When I pulled my motor, that little 2-wire plug on the back left...

Hi, Front main seal was leaking. No noise before. Replaced front main seal and installed a sleeve ...started engine....squeal ....stopped engine ruined crank pulley and cover. Replaced seal ,crank pulley with sleeve and cover. Started engine..squeal .Immediatly shut of engine .Pulled cover and...