3b

Power steering parts off a 3B. $300

Just out of curiousity, why is a diesel engine seal kit called a"GASKET KIT, ENGINE VALVE GRIND" for the 3b engine when the same functionality kit equivalent for the 2F is called "GASKET KIT, ENGINE OVERHAUL" ? I've never owned a diesel nor have I worked on one and was just wondering this out of...

Hello Everyone, I went and looked at to early 80's Canadian BJ60's yesterday, and am looking for some advice One BJ60 had an engine in good condition, but a completely rotton body. I have no experience in body work and do not want to take on that project. The second BJ60 had a reletivly good...

Hello all, I am wondering if anyone has run into this problem... I had a bad oil leak coming from in between my injection pump and the back of my front cover. Upon removing the engine and then injection pump I found there to be no o ring in between there whatsoever, when the manual clearly shows...

For quite some time now, the 3b in my 84 bj60 takes a while to start. In order to start my truck first thing in the day, I turn my key and my glow light comes on for a second, then I have to wait approx. 60 seconds for the glow relay to shut off, then I can turn my key and start the truck. If...

Hi all After cooking my clutch in my 1985 12 volt bj70 on the weekend I have decided to swap in a 24 volt 13 bt sometime in the next week to replace the tired 3b. The 13 bt is a 1989 blue block (8 bolt flywheel) I have read that it is different to the original 3b 6 bolt flywheel. Are the body...

THIS CRUISER IS SOLD!!!! This is a beautiful BJ42! I've had 12 Land Cruisers over the past 18 years and this is by far the nicest one I've owned. Here is a link to a Dropbox folder with approx. 450 pics Dropbox You can see everything on the vehicle in the pictures. Here is the link to the...

This LHD 1982 BJ 42 is a Canadian 24volt cold weather spec cruiser was "restored" 15yrs or so ago and is showing its age on the paint. Some rust in hood and cowl edges. 260K Km but will change as I drive it alot. It looks great still but isn't a con-course resto. I preferred this since I DD this...

Hi there, I live in Las Vegas and lately the temperature has been about 110 F/44 C as always in July. I drive a stock (Canadian) '81 BJ-42 and I noticed that any time the air temp is 105 or more that my 3B just can't stay cool. The temperature keeps climbing and climbing, even when I'm not...

1986 BJ70 imported from Southern Alberta, Canada. Totally stock with the exception of 31 inch tires. Purchased from an older gentleman that used it for cruising through BC in the summer. Vehicle has been repainted at some point in the past. The under-carriage was treated and looks dry and...

The breather tube on my push rod cover on my 84 3B fell off and decided to take a hike down a logging road. Has anyone ever welded a new tube piece on before? The pushrod cover itself is discontinued and I can't seem to find it anywhere. Would I be able to weld it in place if i properly cleaned...

I took the oil pan off to check for sludge and check the integrity of the pan. I side is pristine and no sludge but there were a couple rice grain sized metal chunks and a couple fingernail sized shavings. What else should I inspect before putting the pan back on?

Looking to do a swap to a 40. Looking for non-jdm 3b. Will also take a tranny and transfer if you have. Please pm me.

Howdy, please see the attached pics below. The seller says it's a 2H from a 1980. Need expert's opinion here to confirm if it is indeed a 2H from 1980. Greatly appreciate in advance.

Hey Folks , I have an 82 Canada spec BJ42 with a 3B & 24V system. I am having a PIA issue with my batteries going flat after a few days...particularly when running with the headlights and/or heater blower running. With the regulator disconnected, I am measuring 23.4 volts at idle, and 23.8...

It ONLY does this when it gets warm and comes up to temperature. Has anyone else out there had this same problem ??? Have any ideas? Let me know, thanks Please check the video I'm restoring a BJ40. If you're curious, visit my Facebook page. https://www.facebook.com/lc.bj40/

I have a pile of parts I need to clear out. These are out of a 1984 BJ60, buyer pays shipping from 83702. Intake Manifold - $75 - SOLD, Glenn Exhaust Manifold - $75 Power Steering Pump and Bracket - $100 SOLD, DieselCruiser81 Upper and Lower Thermostat Housing - $50 - SOLD, Georg Valve...

Limited history, out of 1982 BJ42, turns over fine. $700 US funds. Will ship at your expense and you make arrangements. I can put on pallet and secure. 900-1000 lbs. Fastway Freight ships from Porthill, ID 83805

Hi its my first time taking my 3b injectors out and i noticed all 4 have a little creator type divet around the pintle each one slightly different size from one another. The divet area inst concentric to the pintle either Is this supposed to be there or is it wear marks? Do i need all new...

Hi so i was just reading that another forum member here had a precup failiure and someone mentioned that it may have been a cast pre cup I bought new pre cups for my 3b which were going to be installed tommorow but know that i look at it i think it may be cast instead of machined from billet...