1hdt

Hi. Iv got a 1990 HDJ-81 With the 1HDT. How do you get the oil pressure sender out? I need to replace it. Is there a trick to this or do I just need smaller hands? Any help would be great. Thanks. Michael

Hi. Iv got a 1990 HDJ-81 With the 1HDT. How do you get the oil pressure sender out? I need to replace it. Is there a trick to this or do I just need smaller hands? Any help would be great. Thanks. Michael

These Injectors have SOLD! I have a set of 6 injectors (USED) for the 1HDT engine from our 1991 HDJ81 (Japan market, RHD) Land Cruiser that I am selling for $350, plus shipping costs. The injectors have NOT been tested, cleaned, or reconditioned. They are being sold 'as-is' in USED condition...

I was hoping someone could help me out here with a diagnosis and hopefully, an easy fix. I noticed that the corrugated, bent portion of the air intake hose that is AFTER the air filter (probably a foot or so below the air filter along the air intake hose), but BEFORE the turbo, is wet with...

Hi all, Timing belt let go on the 80 and did not end well. Engine is being rebuilt. I started a thread over on 4wd action and thought it would be of interest. Link below. If this breaches rules I'll remove and copy content over. Any feed back welcomed. Cheers Mat...

Following @IanB I'm reposting a question here

Hi, Just a quick question, from what I've found a turbo back exhaust for a 1HDT is the same as for a 1HDFT, am I right? Same turbo flange and mounts. Thanks Cheers

Does the STANDARD aneroid pin allow full fuel at full boost (thinnest part of taper)? Or is it still restricting it in comparison to the main set screw setting? As such, does rotating the aneroid pin affect any change at FULL boost when the pin is fully depressed? I am only talking full boost...

I purchased a kit that included the copper washers but not the o-rings, and I'd rather not pay/wait for shipping from Australia to get them. Does anyone know the dimensions for the 1hdt injector o-rings? I heard Viton rings might be a good upgrade to what Toyota provides. Is there any truth to this?

I decided to perform some minor cylinder head porting and polishing when my engine was apart for a minor overhaul. Researching the forums and looking at common practices with high performance motorcycle and car engines I decided to do some basic cylinder head modifications. If you have any...

Hey guys, I installed a 3inch muffler on my HDJ80 past weekend, and well here are some pros and cons that I found... Pros: 1- More Power, when accelerating the car just accelerates beastly. 2- More torque, when going uphill, it has more torque to stay on a High gear. 3- The sound... It is...

Decided I'll hold on to it and build it. No longer for sale. Thanks for looking 04/05/17 05/02/17 EDIT: Back up for sale, see post number 17

Engine: 4.2L 1HDT (early model 92') Turbo - Grunter Extreme running at 24PSI Non-Intercooled presently Pump rebuilt professionally Injectors have new ND nozzels and setup by professionals Pump has the "power rod" installed I very recently rebuilt my 1HDT. The pump and injectors were also sent...

I have a 1hdt that has done 6000k since full rebuild. It has been blowing blue smoke on start up and at idle since first got it back from Reconditioners. Although it is not using much oil ( 200-300mls per 5000km) it is blowing smoke out oil filler and rocket cover bypass if you open them but...

After mucho searching I have to post up for some help from the experts..does anyone have a pic / diagram of an assembled t belt idler pulley? The below pics describe the questions I have regarding the part..and yes, I took stuff apart and 6 months later tried to put it back together:hillbilly...

Hi there, Pump room of mine is not abe to find the test specification sheet for my 1HDT pump series 096000 - 6760. Anybody in the forum has one that they can share or any other suggestions? They have put the pump on the bench and realised they dont have the sheet with them :-/ Please help...

hi,i am trying to remove the injection pump from a hdj81,everything is loose,have a puller on the front of the shaft,i have tried hammering on the puller shaft,the drive gear is not coming off. any body have experience this? i even tried heating the gear a little after i remove the o ring on the...

Hey all. I've been getting a bit of oil in my coolant system for a few months now. Had it flushed. Now there's more. Anyone seen this or had any experience with it? Kinda freaking me out...

HI I need the lower left timer cover from a 1 HDT (or 1HZ too maybe?) injection pump. Anybody have a junk parts pump or a source for pump parts? Need to get the truck back on the road asap and my cover is cracked.

Does anyone know of a vendor for a good used 1hdt motor? Thanks