What have you done to your Land Cruiser this week?

[Living in the Past]

A wheel spacer is the easiest solution. I've got a couple beat up ones that would be onthe way to becoming beer cans it it wasn't for using them as spare tire spacers.

Cheap 1" spacers off Amazon work great.

 

[ToyotaMatt]

Just doing the usual things this week ..

A little of this and a little of that .

 

[RodrigzCrzr]

Drove the 40 to the local Cars & Coffee in El Segundo.

 

[Pura Vida]

Drove the 40 to the local Cars & Coffee in El Segundo.

View attachment 3231862

That looks like one of those vintage photos

 

[RodrigzCrzr]

That looks like one of those vintage photos

Yeah that’s what I was going for!
Hahaha just kidding.
I phone has been droppped to many times. And the shaking on the motorcycle does a number on them.

 

[micruz60]

Watching the snow pile up on the hibernating 40.

 

[fj40fillet]

Replace all my 79 fuel lines, filter and clamps. Old hose was hard and wasted non ethanol stuff.

 

[Nothinghead]

I tried to remember where I parked it.

 

[Vossie]

Shake down period is going well. Took it to a braai at my uncles and had to enjoy the view

And an artsy one for those who like

 

[aging fleet]

Disassembled three jump seats and created a pair I was happy with. Just need to order fresh mounting hardware and I’ll check this project off the list.

 

[imyahucklbrry]

Started this project over 5 years ago… had to dig out the house caulking that PO used and replace with self leveling sealer

Top sanded and ready…

2 coats of Rustoleum boat primer and 3 coats of paint…

Spraying woulda been better but the foam roller did pretty good……. I haven’t had the top on for quite a while so I’m looking forward to putting it back together - hopefully I’ll remember what goes where!

 

[rex in bama]

Started this project over 5 years ago… had to dig out the house caulking that PO used and replace with self leveling sealer
View attachment 3233060

Top sanded and ready…
View attachment 3233061

2 coats of Rustoleum boat primer and 3 coats of paint…
View attachment 3233062
View attachment 3233063
Spraying woulda been better but the foam roller did pretty good……. I haven’t had the top on for quite a while so I’m looking forward to putting it back together - hopefully I’ll remember what goes where!

What kind of paint did you go with?

 

[imyahucklbrry]

What kind of paint did you go with?

 

[Godwin]

40 on the farm, getting a few trees cut before the rains hit.

 

[120mm]

Spent the week troubleshooting a starting issue. Has taken nearly a year to get to this point


Finally discovered the pickup tube was plugged with tank sealant.

Once I cleared the plug, the tank immediately started leaking from the seams....

Dang it.

 

[Roastchestnuts]

Cant remember If I posted this or not. But I got a bunch of photos finally scanned and developed. This photo from of the salt wagon pre sill replacement! I took this photo with my hasselblad and the 80mm planar. film: Fuji Pro400H

 

[Shark56]

View attachment 3233838Cant remember If I posted this or not. But I got a bunch of photos finally scanned and developed. This photo from of the salt wagon pre sill replacement! I took this photo with my hasselblad and the 80mm planar. film: Fuji Pro400H

Toyota Trails stuff there!

 

[Roastchestnuts]

Toyota Trails stuff there!

Thanks!

 

[ryanwk628]

View attachment 3233185View attachment 3233186

I am considering the same. Did you tip it after rolling?

 

[imyahucklbrry]

I am considering the same. Did you tip it after rolling?

I did not…. It didn’t seem to have air bubbles so I skipped that
I may wet sand and apply one last coat… mostly because I have enough paint!