GSMTR

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

GSMTR online registration is still open and will remain open until 6 AM Friday May 11. You can register at the event but if you don’t pre register you may not get a T-shirt.
Looking forward to seeing you all there.
 
Made a slight horsepower addition this weekend.

image-2069280536.webp
 
NICE!!!

You are guaranteed to break something now, with all that added power :flipoff2:
 
pfran42 said:
What is 3G/4G T-Mobile coverage like at Golden Mountain? I plan on running a GMSTR feed to a couple of sites and need to plan accordingly.
Click to expand...

spotty if I recall correctly.
 
pfran42 said:
What is 3G/4G T-Mobile coverage like at Golden Mountain? I plan on running a GMSTR feed to a couple of sites and need to plan accordingly.
Click to expand...

My sprint service 3G works pretty good! Even on the trails :)
 
Anybody have or know of any mini-truck driveshafts or yokes they could pick up and bring to GSMTR for me? I'm quite sure my rear d-shaft isn't going to survive long and I didn't have the correct yokes to make one.

Anybody need 1st gen (small hole/small pattern) shafts? I have a few of those and I don't need them now.
 
4xsteve said:
Anybody have or know of any mini-truck driveshafts or yokes they could pick up and bring to GSMTR for me? I'm quite sure my rear d-shaft isn't going to survive long and I didn't have the correct yokes to make one.

Anybody need 1st gen (small hole/small pattern) shafts? I have a few of those and I don't need them now.
Click to expand...

You wouldn't happen to have a rear first gen long bed drive shaft? Mine is bent badly.
 
4xsteve said:
Anybody have or know of any mini-truck driveshafts or yokes they could pick up and bring to GSMTR for me? I'm quite sure my rear d-shaft isn't going to survive long and I didn't have the correct yokes to make one.

Anybody need 1st gen (small hole/small pattern) shafts? I have a few of those and I don't need them now.
Click to expand...

Lowe Toyota said:
You wouldn't happen to have a rear first gen long bed drive shaft? Mine is bent badly.
Click to expand...

I love how you guys wait till the last minute to fix your junk. If you were fully prepared like me you'd have your truck packed already, a tune up done and tires rotated. :flipoff2:
 
tkinze said:
I love how you guys wait till the last minute to fix your junk. If you were fully prepared like me you'd have your truck packed already, a tune up done and tires rotated. :flipoff2:
Click to expand...


RIGHT!!!!!!

get your :censor: truck off the lift then :flipoff2:
 
AuburnFJsexy said:
RIGHT!!!!!!

get your :censor: truck off the lift then :flipoff2:
Click to expand...


hahahahahahahahaha! laugin' my arse off!

pickin' up the diff today re-geared and ready to go. Golly I have soooooo much to do to get ready.
 
Lowe Toyota said:
You wouldn't happen to have a rear first gen long bed drive shaft? Mine is bent badly.
Click to expand...

Sure do. I have even have your choice of grey or red. :)
Can you verify for me your tube length though just to be sure? And, also to verify, yours is course spline, right?

Any other 1st gen stuff needed? I've parted out three; 2 LWB and 1 SWB. Fenders, motors, trans, cases, clusters, diffs, axles, etc. I don't need almost any of it anymore.
 
tkinze said:
hahahahahahahahaha! laugin' my arse off!

pickin' up the diff today re-geared and ready to go. Golly I have soooooo much to do to get ready.
Click to expand...


I have a lot to do before we leave too :bang:

Picking up the open front axle today and the locker will be delivered tomorrow or Friday...
 
tkinze said:
I love how you guys wait till the last minute to fix your junk. If you were fully prepared like me you'd have your truck packed already, a tune up done and tires rotated. :flipoff2:
Click to expand...

Ask me about the WHOLE story at GSMTR and I'll give you the full rundown on my last-minute truck "woes" (read "nightmares").

I know you're being facetious Ted but FYI, I've been working every day, 7 days a week, 5-8 hours a day, since about April 20th, getting my junk(s) ready. So much so that my cuticles are actually stained with grunge. Haha.

How you plannin to break in those gears?
 
4xsteve said:
How you plannin to break in those gears?
Click to expand...

my backup tow vehicle fell through so as of right now the drive up will be the break in, cringe! :bang:

I have faith that white rice will get me there,...and back :hhmm:
 
You must log in or register to reply here.

Share this page

Back
Top Bottom