Good article on JIS screws

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Great article! My Cruiser is actually insured with them.
Any chance you know the correct JIS screw for the 40 series instrument cluster? I was hoping to see them on your website but didn't.

Edit: Upon further searching I found these: Gauge Cluster | Marine Grade Stainless Hardware & Screw Kit | Toyota Land Cruiser FJ40 - https://www.overlandmetric.com/collections/stainless-hardware-kits/products/gauge-cluster-marine-grade-stainless-oval-head-fj40

Would prefer OEM look to stainless though.
 
Last edited:
What is the thread pattern, pitch and length of OEM? I,m looking to get slightly longer for mounting Dakota Digital cluster. The original screws work but longer would be better. Thinking McMaster-Carr might have. Thanks.
 
Any chance you know the correct JIS screw for the 40 series instrument cluster? I was hoping to see them on your website but didn't.

Edit: Upon further searching I found these: Gauge Cluster | Marine Grade Stainless Hardware & Screw Kit | Toyota Land Cruiser FJ40 - https://www.overlandmetric.com/collections/stainless-hardware-kits/products/gauge-cluster-marine-grade-stainless-oval-head-fj40

Would prefer OEM look to stainless though.

FYI, if you're already placing an order with CR, they are on the site.
 
What is the thread pattern, pitch and length of OEM? I,m looking to get slightly longer for mounting Dakota Digital cluster. The original screws work but longer would be better. Thinking McMaster-Carr might have. Thanks.
There is a way to decipher that simply based on the part number. I think Overland Metric’s site has some details about some of the info, which I’ve often used to figure out that info.
 
Looks like from cross referencing the OEM part number with Overland Metric's table that the screws are M6 x 12 Phillips head oval. McMaster-Carr has M6 JIS Stainless Steel Pan Head Screws 16 mm which I may try for the DD instrument cluster.
 
Looks like from cross referencing the OEM part number with Overland Metric's table that the screws are M6 x 12 Phillips head oval. McMaster-Carr has M6 JIS Stainless Steel Pan Head Screws 16 mm which I may try for the DD instrument cluster.
I didn’t know that stock had gone obsolete?
 
OEM Part 93230-26012 - Seems like I've ordered these before, but the heads were smaller than the two screws I had in my gauge cluster. The existing screws in my cluster possibly may not be OEM, so there is that.
I don’t have my master catalog in front of me, but that PN looks right.
 
Wow, walked into my shop and knew right where they were. Here a pic of the new OEM screws vs what I have installed.
48AD1C82-E6E8-4DFF-BA15-6A701F1E7E8A.jpeg


E7D58050-E892-4DC9-9905-823FD84589C9.jpeg


615BE664-8B43-4102-9BF8-FDD5BDF8AE43.jpeg
 
Anyone have any insight on the Instrument Panel screws (4 total)? Part number for my 1983 is 93520-26020. Seems to be NLA. Looks like that number is only applicable for 80-84 FJ or BJ4X.

To be clear, I'm referring to the 4 screws that hold the instrument panel on, not the 2 screws that hold the instrument cluster.
 
If they’re oval head, order hood hinge screws for the pre-79 hinges. IIRC the suffix code also calls for an 020 length.
 
If they’re oval head, order hood hinge screws for the pre-79 hinges. IIRC the suffix code also calls for an 020 length.
Thanks. The ones in my Troopy are not oval head but they also might not be OEM.
 
Back
Top Bottom