Front bumper opinions needed.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 3, 2006
Threads
74
Messages
313
Location
Weatherford, OK
I'm wanting to install a new bumper on the front of my rig. I can't decide if I want to run an HFS bumper from CCOT or an ARB. I like the looks of both and know the ARB stuff gets good comments. I'm just looking for opinions. BTW, I plan on outfitting it with a new Warn 8274-50. Thanks!
 
I also like the HFS bumper from CCOT. The only issue and it is minor for most, is that in a number of states that bumper is illegal for use on state roads due to the length (too short) of the bumper. I do not think there is another one on the market that is as stout as that HFS bumper.
 
only problem with super stout bumpers. Something else typically bends instead of the bumper...
 
Thanks guys. I really like that one too. That was my original plan and is cheaper than ARB.
 
I recently ordered one of the HFS bumpers but am dissapointed in the quality. I should have sent it back but never got around to it. A couple of weeks after ordering I hadn't received it yet so called CCOT to find out status. I was told that the last batch that came in were very rough and they didn't think powder coating would cover up the imperfections so they refused them. A few weeks later my bumper showed up but you can still see where there was a lot of grinding done that is still visible despite the powder coating. Its also not the best powder coating job either. Maybe I'm too much of a perfectionist but I'm still looking for a nice winch bumper for my '80 FJ40 restoration.
 
get some mad skills and make one of your own. get everything you want for half the price,
 
JRFJ4- said:
Be original. Don't get what everyone else has.

OR support a Mud guy and get that killer one made by HawkDriver
 
wantatlc said:
OR support a Mud guy and get that killer one made by HawkDriver

If I were to buy something, it would definately be from a mudder. I don't like the HFS or ARB units.

HawkDriver does have some cool stuff.


JR
 
wantatlc said:
OR support a Mud guy and get that killer one made by HawkDriver


HawkDriver is an excellent fabber and a really nice guy. I have one of his bumpers that I modified for a winch. Although I do agree with Jason that the heavier the bumper the more likely damage will result elsewhere.
I think Jeremy is out of the bumper-making biz until he is back from....over there.

Ed
warn8274 007.webp
 
Degnol said:
I think Jeremy is out of the bumper-making biz until he is back from....over there.

Ed

Right you are Ed. :frown: But when I get back it's awn! Oh, nice work by the way. Looks great. :)

Thanks fellas. I'm all for going down the road of building your skillz and fabbing up your own stuff but that's a convenience that some folks just don't have or havn't invested in.

I do like the MAF 4 plus ones, and the HFS is pretty nice. Then there's bulletproof mfg as well. All good designs by me.

Jeremy
 
Mace said:
only problem with super stout bumpers. Something else typically bends instead of the bumper...

Yup. If I hit something hard enough to bend the bumper, I'd rather have it bend then something else on the frame. 10 minutes to change a bumper vs. straightening a frame. ;)
 
Comeawn now, this is apples & oranges here. The HFS & CCOT bumpers look like a simple channel with a plate welded on the rear & recovery brackets welded on the front with a few mounting holes drilled.

Now the ARB unit, not even close to a comparison. Look at all the complex bends & the prebent tubes. It has many more contours too. It'd be too wide & bulky for my use though.... Soooo, I vote for homeade!
 
Back
Top Bottom