FJ40 Power Steering - what's wrong when...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 30, 2005
Threads
50
Messages
169
...there is no assistance at idle?

Hello group!

Oil level is fine and belt is not slipping but there is often no assitance when the engine runs at idle.

There is almost immediate assistance when I rev it a little.

(1982 FJ40 2F)

What could that be?
Any tests I could do?

Kind regards
Bernt
 
what ps system are you running or talking about might help a bit.
 
Did you bleed the system?
1. Wheels off the ground
2. Turn steering wheel form left to right or right to left, at least 20 times to get all the air out of the system.
3. Check fluid.
 
Hi,

It is the Toyota FJ40 power steering and pump. It is all original as it came.

I did not bleed it but I also did not have it apart. It had been fine for the first month I owned the vehicle but now in the second, it is doing this.

Regards
Bernt
 
Swap it out for a Saginaw pump with a smaller pulley. I have the bracket to mount the pump and #'s for a pulley that is smaller so you won't have that problem at low RPM's. Bill

I have both brackets to do the Mini truck gearbox and
the Saginaw P/S pump.That includes all the mounting
hardware,spacers and adjusting arm.
They are $95.00 each plus shipping. If you buy both
they are $180.00 plus shipping.
Send me your address and what you want and I will
email you a total.
You can see pictures at the below web site and a good
post on ih8mud. Thanks
Bill

http://photos.yahoo.com/wdorry
https://forum.ih8mud.com/showthread.php?t=65318
 
berntd said:
...there is no assistance at idle?

Hello group!

Oil level is fine and belt is not slipping but there is often no assitance when the engine runs at idle.

There is almost immediate assistance when I rev it a little.

(1982 FJ40 2F)

What could that be?
Any tests I could do?

Kind regards
Bernt

I had this exact same problem after I converted to power steering.

I changed out PS pump and the problem went away.

I could turn the tires with the motor at an idle and the FJ stopped with one finger.
 
wesintl said:
I'd say the pump needs some work. Same thing occured on my 60 pump which is the same thing. A $30 rebuild kit from the dealer and it was ok again.

Concur - both the cheapest solution, and probably something that should be considered "maintenance", anyway.

Freshen up with new seals.

PS pump rebuild == :banana:.

Only problem that is tough is if the shaft bearing surfaces are worn, as there is no replaceable bearing/bushing. A machine shop can bush and hone, but that's gonna be expensive...OTOH, new OEM PS pump is ~$480, so "expensive" is relative...

PS Gear box is tougher - I'm currently making analogues for the SSTs required.

HTH

Kirk
 
I rebuilt my my pump and I still had problems. I bought it used and there is not telling where it came from or if the previous owner tried messing with it so I ran it like that for a while until it started leaking.....agian. Anyhow, long story short, I finally borke the piggy bank and ran down to O'rilelly's auto parts store and bought me one with a lifetime warranty.....It works now. I did not look around to see if anyone else had a good deal.
 
Hello all.

From the replys, it looks like it is probably the pump then.
Is this kit something I can install myself (I can rebuild engines) or does it need a ton of special tools?

Is it a kit for the complete unit or is there a seperate one for the pressure valve in there?

Hey, today it worked again like new but then again, it is a cooler day - strange...

Where would I get a smaller pulley from?


Regards
Bernt
 
wesintl said:
I'd say the pump needs some work. Same thing occured on my 60 pump which is the same thing. A $30 rebuild kit from the dealer and it was ok again.

How long ago wass that Wes? I thought those kist no longer existed...
 
PabloCruise said:
How long ago wass that Wes? I thought those kist no longer existed...

probably ~4 years back. I'll dig up the reciept and post the part #. I can't see it not being good though it'll work on a 62 pump as well. It's just a bunch of seals. IIRC Not difficult as kirk mentions.
 
wesintl said:
probably ~4 years back. I'll dig up the reciept and post the part #. I can't see it not being good though it'll work on a 62 pump as well. It's just a bunch of seals. IIRC Not difficult as kirk mentions.

Just received a rebuild kit from CDan in December, so it's still available.

The PS pump rebuild is *easy*, unless the shaft bearing surfaces are worn. If that's the case, get another used pump - they are commonly available at $60-$80 off of FJ60 trucks.

If the shaft bearing surfaces are worn, either on the shaft, or in the end caps, the shaft can be trued, and the end caps bushed and honed, but the cost is substantial if you have someone do it.

Note that SOR doesn't sell rebuilt OEM pumps for this very reason.

Took me less than two hours to rebuild my pump. No special tools required, other than a pull scale for checking the preload. FSM is very good on the procedure.

Kirk
 
From what I remember, the kit contains nothing but a bunch of O-rings. As suggested by Largenfirm, this kit may or may not fix the ps pump if you have other worn out parts. I rebuilt two pumps one seemed to work and then started leaking, the other is still working. After one try on one them, I bought a rebuilt one.
 
fjwagon said:
From what I remember, the kit contains nothing but a bunch of O-rings. As suggested by Largenfirm, this kit may or may not fix the ps pump if you have other worn out parts. I rebuilt two pumps one seemed to work and then started leaking, the other is still working. After one try on one them, I bought a rebuilt one.

Close - one internal snap ring, one steel seal with a rubber lining, one brass seat for the high-pressure attach, and about 16 o-rings of various sizes and compositions (some grey, some black).

Toyota PN is 04446-30010, list around $56, $44 from CDan.

Kirk
 
:) Yep, that sound like it. Thanks for the correction.

largenfirm said:
Close - one internal snap ring, one steel seal with a rubber lining, one brass seat for the high-pressure attach, and about 16 o-rings of various sizes and compositions (some grey, some black).

Toyota PN is 04446-30010, list around $56, $44 from CDan.

Kirk
 
Back
Top Bottom