F or 2F

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 3, 2006
Threads
74
Messages
313
Location
Weatherford, OK
I have a 74 f and a 78 2f with smog that both need rebuilt. Assuming both are re-buildable and in similar condition internally, which one should i overhaul and put in my 74 fj40? Ive heard of de-smogging issues, could this be a problem? Also would you run either factory carb (rebuilt) or try webber or fuel injection? Any suggestions or ideas would be much appreciated. Thanks
 
Last edited:
You may have trouble finding pistons for the '74, is that a late F engine?
I would rebuild the 2F block, put the '74 intake & carb on it, if it is a late F I'd put that head on the 2F block.
Desmogging should be no problem.
 
It is a late f and it's the one I've been running since Ive owned my cruiser. When I bought it I was given a 78 40 with the 2f. I have all the parts for it but I like the sound of running f intake and carb since Mark rebuilt my carb a while back.
 
I built my last engine (still running it) almost 10 years ago out of an early 2F block with my original Late f head. Kept most of my '74 peripherals. Remember that the oil pressure sender hole in the F doesn't work in the 2F...you nee to use either the oil cooler or a oil filter mount tapped for the sender. Front motor mounts are different too.
 
Thanks. Ill keep thoee things in mind. I have a trusted machinist, would it be best to have him get parts and while I'm at it whi would you recommend getting a clutch from?
 
Always best to have your machinist order the engine parts...he gets a better price and the parts will fit. I had my shop install cam bearings, I put everything else together. Machinist can get an OEM clutch & pressure plate...have them all balanced.
 
Hi all,

When I bought my '74 FJ40 it had a '78 2F running the original '74 F carb, with the '78 fully electronic ignition. I later installed a rebuilt and de-smogged '77 2F carb.
I did not noticed much difference in performance between the late F carb and the early 2F carb.

Good luck!

Alan


It is a late f and it's the one I've been running since Ive owned my cruiser. When I bought it I was given a 78 40 with the 2f. I have all the parts for it but I like the sound of running f intake and carb since Mark rebuilt my carb a while back.
 
I prefer running my (original, Jim C. rebuilt) '74 carb. Last of the mechanical secondary carbs. I just prefer mechanical to vacuum...
 
X2 - Since you already have some of the parts....
The one thing the previous owner of my 40 did right was to install a shaved F head off of a '74 onto the stock block of my '76 2F. If I remember correctly it was shaved .020 and had flat top pistons. Kind of a high compression hybrid F/2F. I was using the stock '76 carb that JimC had rebuilt as well. Used to cruise 85 mph easily on the freeway with pedal to spare and always outpaced other 2F's friends had in their 40's.
Sadly lost this engine to oil starvation after 8 years. Somehow snapped off the oil pump drive tip of the distributer doing 60 mph. Seized beyond repair. I replaced it with a 2F out of an '84 FJ60 about 10 years ago and while this engine runs great it definitely has less horsepower than the previous engine. Miss that power especially when I'm "combat driving" in the 40 with the modern, fast cars of today. Good luck! :cool:




I built my last engine (still running it) almost 10 years ago out of an early 2F block with my original Late f head. Kept most of my '74 peripherals.
 
I also have a 2F with F carb, and electronic dizzy
 
I built my last engine (still running it) almost 10 years ago out of an early 2F block with my original Late f head. Kept most of my '74 peripherals. Remember that the oil pressure sender hole in the F doesn't work in the 2F...you nee to use either the oil cooler or a oil filter mount tapped for the sender. Front motor mounts are different too.
Pighead I am purchasing a 1983 2F out of an FJ60. From what I have read the motor mounts are the same, F vs 2F but you say they are different. I will presume this will be obvious when I pick up the engine? Are you referring to the iron or the rubber? I know when I bought new motor mounts they were square vs round in the front, but installation was no problem. I also understand I may have to do something with the water pump? My 1970 FJ40 has a 2F radiator shroud. So that with my F engine I really should install a spacer to move the fan forward. So I'm thinking that will not be an issue with the swap as the an will already be moved forward. Any advice you can offer will be greatly appreciated. I will haul the engine down from Quito to Cuenca on a pallet in the back of the 40 and take it straight to the shop that does my heavy work. I'm not sure what I will find with regards to smog since this FJ60 is non-USA. I have read some stuff about plugging some smog holes. I will be running an MAF 6-1 header.

IMG-20150424-WA0016.webp


DSCN3032.webp


DSCN3698.webp
 
we used FJ60 motor mounts for my 2F when the original ones from the F engine went out - both the metal and rubber were replaced at the same time - got the mounts from Kurt at cruiseroutfitters.com
 
Thanks Claudia, I think I bought my mounts from CCOT, they worked fine and I have only 8,000 miles on the rig since I installed them. Kind of surprised at how the rear mounts work and that left rear is a sonofagun to get to. Whew, looking at that picture I sure am glad I cleaned that area up. The new motor should have PCV, that will be better than the road draft tube dripping on the front drive shaft.

DSCN1710.webp
 
we used FJ60 motor mounts for my 2F when the original ones from the F engine went out - both the metal and rubber were replaced at the same time - got the mounts from Kurt at cruiseroutfitters.com
Claudia, can you look at this picture please and advise. I see a plug installed at the rear of the block below the exhaust manifold. Looks like the same place my oil pressure sending unit is mounted on my F. Is that correct, I can use that location? I don't see a place towards the rear of the engine where my water temperature sending unit is mounted. It would actually be better to have it closer to the thermostat so actual and shown temperatures would be closer than current. Can you straighten me out on where these sending units are placed on your 2F? Thank you.

IMG-20150424-WA0011.webp
 
FWIW - The water temp sending unit should be located on top of the head, behind the carb towards the rear of the head. There should be two holes, one for the water temp sensor and the other for the heater hose return line.

photo%25201.JPG


I do believe the plug you are referencing below the exhaust manifold is for the block drain.
 
Oil pressure should be on the oil filter mount.

Your temp sender is on the top of the head to the left of the brake booster vac line (in the pic)
 
Thank you. If you look at the first picture, down by the date stamp you can see where the oil sending unit is mounted on my F engine. I believe the drain bolt you are referring to would be just up and to the rear of that sending unit. Does the 2F have a similar location for the oil pressure sending unit?

In the second picture you can see my water temp sending unit and a plugged location next to it. I think that is like the two holes you referred to so I will "guess" that the 2F is what you showed and so I can mount the water temp unit there like on my F. I won't see the motor until next Monday when I drive up to Quito but I'm trying to prepare my mind for what I will need to address when I get it home. Thanks for your help and input.

DSCN1732.webp


DSCN2710.webp
 
Oil pressure should be on the oil filter mount.

Your temp sender is on the top of the head to the left of the brake booster vac line (in the pic)

Can you see the area you are referring to in this picture? Quite different from my F engine which has plumbing for the filter and of course is on the drivers side. The sending unit many inches away from the filter mount also. Thanks for your input and help.

IMG-20150424-WA0012.webp
 
The 2F Oil sensor should be on the oil filter bracket.
dsc07040-jpg.865087

or
img_3128-jpg.336641


Yes, you can install the water temp sensor like your F engine.
IMG_0334.jpg
 
Back
Top Bottom