Clutch-ing Offroad

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 31, 2005
Threads
31
Messages
230
Location
Honolulu, HI
Alright, I admit, I'm a noob to manuals.
So I understand that torque convertors are at an advantage off road, but the 40, being a manual, has a clutch. Now... I know what it does, and basically how it works, and how to use it on-road. But how do you use it off road? School me!
 
Go find a low traffic area off road or on, put the truck in 4 low, and drive around for a while...it is the same, only slower.



player said:
So I understand that torque convertors are at an advantage off road...


This is only an advantage to the specific operator...



Good luck!



-Steve
 
You can't really ride the clutch and take `advantage' of that per se. Advantage off road is if your cruiser won't start you can roll-start it, it's easier to understand than a slushbox, and takes good-ol 90wt.

Other than that, I'd say learn how to double-clutch and get her in & out of gear sans clutch (other than 1st it's easy to do, just match RPMs) for worst case scenarios.

Other than that are you referring to something specific?
 
Hi All:

When off-road, you will need to learn how to "read" trail conditions so to choose the correct gear to use to tackle the given obstacle. Once you've choosen a gear stay with it, especially if going through deep water or mud.

So, that being said, off-road you don't want to engage the clutch any more than absolutely neccesary!

Regards,

Alan
Seattle
 
I'm a big fan of slowly getting the front tires up an obsticle, then grabbing a higher gear and flooring it :D
 
I find an automatic is more convenient offroad, but manual is a lot more fun. Kind of like the difference between a schooner and a sailboat or a jet and a propeller plane. The hand throttle sure helps.
 
don't clutch until you know your rig and your clutch well. you can lug until it stalls then either pop the clutch (on down hill), or bump start it on uphill...clutches can throw newbies into really bad situations.
 
I recommend Ige's approach. You should find some bunny slopes near you and definitely lug your vehicle down in different gears and speeds with the aim of finding out how much slope your specific vehicle can handle at specific speeds before it stalls. Most noobs hit the clutch way too soon and never get the feel of how torquey the bottom end of a Toyota engine is. Stalling is definitely part of the learning curve. Ask the Calico Kid!

If you find that you like spending a lot of time in the rocks, lower gears can greatly increase your odds of keeping the vehicle moving at slow speeds without stalling.:cool:
 
:) to add mark's post, stalling is way more cool than pushing in the clutch and careening uncontollably down some obstacle, so don't worry about feelilng like an idiot if you stall.
like he said, find a local place where you can't kill yourself if you clutch and see just what your cruiser can lug...you'll probably be surprised. i've even gotten my non modified v8 to the point where it idles at about 550 rpms before it dies! i almost never use my clutch.

i find the gear i need for the obstacle and stay there, but then, the only time i've driven autos was a brief time about 13 years ago when i royally screwed up my foot (swapped with my ex), so i'm pretty good with my manuals (and yes, i still stall them). my first car was even a stick...traded a thoroughbred for it before i even had a license :)
 
You guys are great. Mud has more love going around then any other forum out there. In a odd twisted way... :D but thats besides the point. :bounce:

3fj40 said:
You can't really ride the clutch and take `advantage' of that per se. Advantage off road is if your cruiser won't start you can roll-start it, it's easier to understand than a slushbox, and takes good-ol 90wt.

Other than that, I'd say learn how to double-clutch and get her in & out of gear sans clutch (other than 1st it's easy to do, just match RPMs) for worst case scenarios.

Other than that are you referring to something specific?


Err, whats he mean by worst case scenario? And uh, whats a bump-start?

Stalling the engine won't have any... negative effects on it, will it?

Happy Chrismas, and a Merry NewYears,
Trevor
 
1. you clutch only when shifting gears.
a. some might say there could be times when you would need to ride the clutch like a two-stroke motorcyle.

2. worst case scenario, they have hydraulic clutchs, so there is plumbing involved, a master cly and a slave cyl. a broken line or blown seal will render the clutch pedal useless.
a. it is possible to drive a standard trany without using the clutch pedal.

3. if the starter or battery dies, you can start the truck by getting it rolling, put it gear and "side step" the clutch.

4. the only "negative" effect of stalling, if you do it ALOT is killing your starter or battery. but both would need to be old and well used and you would REALLY needing to be stalling it alot.
 
if you stall, a lot of times, you just bump the starter and the torque of the engine will catch...give it a tap of the gas and its running and pulling you again...you never touch the clutch. it's not real smooth, but you're expecting it so no biggie
 
Oh, it makes sense now!
Now, more questions.
Whats side stepping the clutch?
And uh, how would you drive w/o a operating clutch? And when would you have to ride the clutch?
-Trevor
 
i have the 3-speed trans, and i find that 2nd-gear in low-range is awesome for attacking hills. you can jam it into 3rd quickly once you need upshift.

something else you can do with a clutch (incase someone else didn't mention it)
is if you stall on a hill, you can put a foot on the brake, and one on the clutch (both pushed all the way down). start the engine, and let the clutch out about half way while your still holding the brake in. this will allow you ride the clutch long enough to get your right foot from the brake to the gas pedal. don't do if for a long time or you'll smoke the clutch, but it works in tight situations.

oh yeah, if you have parking brake (mine's been removed) then you won't need to use this clutch trick.
 
i find myself ridin the clutch a good bit in tight situations. This is probably really bad but it seems necessary?
 
So, what if I was near stallin, then I kept giving it more accelerator? Wouldnt that increase the RPMs and make it not stall?
 
yes, but then you might have too much speed for the trail ahead.


side stepping the clutch is exactly what it sounds like, put the clutch to the floor and then slip your foot off the side (engaging it really quickly)
 
player said:
And uh, how would you drive w/o a operating clutch?

it's harder to explain then it is to actually do.

from a stop kill the engine
put it in gear and start it(without using the clutch), it will be rough but it'll go.

shifting has a "feel" to it, that i can't explain in words, you'll need to figure that for yourself. but you just lift off the gas and pull it into second. like i said there's timing involved, when you do it right it will "click" into gear, when done improperly you'll "grind" the gears. don't force it and don't pull that shifter as fast as you can, just move the shifter as you normally would.
it's easier than it sounds.

it's also possible to down shift as well, however that's a bit more of a "challenge".

this is a good skill to have, more so when driving 30 year old trucks. it has got me home more then a few times already.


if you have access to a front wheel drive car with a stanard trany, they're a breeze to do this on. i rarely use the clutch on our celica, other than pulling out.
 
Back
Top Bottom